Installation Instructions
Page 3
... 4 ft. (1.22 m) long. Check existing electrical supply and venting. Check local codes. Check that opens to your installation. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with dryer) Refer to 1" (25mm) or hex-head socket wrench Parts supplied: Parts package is a registered trademark of Saturn Fasteners, Inc...
... 4 ft. (1.22 m) long. Check existing electrical supply and venting. Check local codes. Check that opens to your installation. Short inlet hose Long inlet hose Rubber washer Optional Equipment: (Not supplied with dryer) Refer to 1" (25mm) or hex-head socket wrench Parts supplied: Parts package is a registered trademark of Saturn Fasteners, Inc...
Installation Instructions
Page 4
... limit, or do not permit, installing dryer in door are provided. ■■Level floor with elbow. You may use the water supply for your washer using a pedestal, you will need 18" (460 mm) to shut off at end of 5" (127 mm) clearance behind dryer for walls, doors, and floor moldings...
... limit, or do not permit, installing dryer in door are provided. ■■Level floor with elbow. You may use the water supply for your washer using a pedestal, you will need 18" (460 mm) to shut off at end of 5" (127 mm) clearance behind dryer for walls, doors, and floor moldings...
Installation Instructions
Page 15
... caulking compound to the cold water faucet. See figure A. See figure B. Record hose installation or replacement dates on connector. 15 Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. NOTE: Replace inlet hoses after 5 years of the "Y" connector to seal exterior ... If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be connected to exhaust hood with new rubber washer provided. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose...
... caulking compound to the cold water faucet. See figure A. See figure B. Record hose installation or replacement dates on connector. 15 Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. NOTE: Replace inlet hoses after 5 years of the "Y" connector to seal exterior ... If "Y" connector cannot be attached directly to the cold water faucet, the short hose must be connected to exhaust hood with new rubber washer provided. Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. 1. Turn cold water off, remove hose...
Installation Instructions
Page 16
.... Attach this end to the coupling can result. 4. Damage to the coupling can result. 6. Damage to fill valve at bottom of dryer back panel. Attach washer cold inlet hose to other end of long hose to the coupling can result. Check for leaks Check for leaks around "Y" connector, faucet, and hoses...
.... Attach this end to the coupling can result. 4. Damage to the coupling can result. 6. Damage to fill valve at bottom of dryer back panel. Attach washer cold inlet hose to other end of long hose to the coupling can result. Check for leaks Check for leaks around "Y" connector, faucet, and hoses...
Owners Manual
Page 4
... at a premium, the stack kit allows the dryer to a more information on top of the washer. 4 The large drawer provides convenient storage. Stack Kit If space is at : www.whirlpool.com/accessories. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. In Canada, call 1-800-901-2042, or visit...
... at a premium, the stack kit allows the dryer to a more information on top of the washer. 4 The large drawer provides convenient storage. Stack Kit If space is at : www.whirlpool.com/accessories. Worksurface The worksurface bridges the washer and dryer, and provides a convenient working height. In Canada, call 1-800-901-2042, or visit...