Whirlpool WED8900BC Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED8900BC manuals!
Problems with Whirlpool WED8900BC?
Ask a Question
Free Whirlpool WED8900BC manuals!
Problems with Whirlpool WED8900BC?
Ask a Question
Most Recent Whirlpool WED8900BC Questions
My Dryer Whirpool Dryer Turns On But It Won’t Start It Makes A Noise How Do I
how do I reset my whirlpool dryer it turns on but won't start
how do I reset my whirlpool dryer it turns on but won't start
(Posted by Watchmework111 4 years ago)
Can't Vent Out Bottom Of Electric Dryer??
(Posted by franktsunkel 10 years ago)
Whirlpool WED8900BC Videos
Price Drop WED8900BC Whirlpool Cabrio Platinum 7.6 Cu. Ft. 14-Cycle Steam Chrome Shadow
Duration: :44
Total Views: 0
Duration: :44
Total Views: 0
Popular Whirlpool WED8900BC Manual Pages
Ventilation Specification - Page 4
... from laundry area. See the Installation Instructions for the specific dryer model being used for balancing out the overall duct system.
■ Design the central duct system for sufficient capacity to handle the maximum number of dryers operated at the connection between the vent system and the dryer's vent pipe, for Whirlpool Corporation dryers sold in compliance:
1. To avoid...
Ventilation Specification - Page 5
... Approvals
All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that a dryer is allowed 40 ft (12.2 m) of total vent length with vents
*Required spacing Installation spacing for recessed area or closet The dimensions shown are sold in which the Installation Instructions do not address the vent length for the specific number...
Ventilation Specification - Page 6
...
system design) G. Recommended room venting and installation spacing for an example of a generic vertical system.
Weighted dampers C. Barometric damper (use depends on each application. Individual dryer exhaust -
Each dryer is free of lint and debris.
■ Confirm that have airflow detection capabilities. (See specific model product literature for the type of vent you...
Use & Care Guide - Page 4
...-free finish may cause temporary staining on some models) cycle is best for reducing odors and light wrinkles in good air flow.
It may yield better results than four 90° elbows in the dryer. n Use the shortest length of dry garments.
each load. See Installation Instructions.
n Replace plastic or foil vent material
with heat...
Use & Care Guide - Page 10
... not remove the lint screen. 1. The drying rack is intended for use . Replace all parts and panels before servicing. Select the Air Only, Low or Extra Low Temp setting. Turn bulb counterclockwise. Allow space around items for air to leave adequate clearance between drying rack grille.
4. Plug in your dryer drum. WARNING
Electrical Shock Hazard Disconnect power...
Use & Care Guide - Page 12
... MOVING CARE
Install and store your dryer where it . If you will not freeze. Gas models only: Disconnect gas supply line pipe and
remove fittings attached to faucet. Transport hose separately. 7. Disconnect water inlet hose from
faucet, then drain the hose. Reconnect water inlet hose to dryer pipe. 4. Replace all parts and panels before servicing. Steam models only: Disconnect...
Use & Care Guide - Page 13
...'t been used during Automatic cycles. See the Installation Instructions. On gas dryers, you do not feel air movement, clean exhaust system of lint or replace exhaust vent with Steam cycle selected (on some models)
Water inlet valve on the gas supply line is normal. The Air Only temperature setting has Select the right temperature for assistance and...
Use & Care Guide - Page 14
... overloaded. Cycle time is connected to both the faucet and dryer's water inlet valve. See "Installation Instructions".
Dry clean only garments are left in clothes.
The dryer is connected to garment care label instructions.
All four dryer sensor strips on fabric type. Change the dryness level setting on load
Improper use fabric softener sheets with temperature below...
Use & Care Guide - Page 15
... dryer control has detected a problem that requires service.
Press any key to avoid overdrying the load. If the message persists, consult a qualified electrician.
Confirm the power cord is present. Replace the fuse or reset the circuit breaker. Call for service.
15 Using Timed Dry Cycle with a lower heat setting to clear the code from turning on.
TROUBLESHOOTING
First...
Use & Care Guide - Page 16
...in an inaccessible location or is installed, operated, and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will need for Factory Specified Replacement Parts and repair labor to resolve
the problem after checking "Troubleshooting," additional help you obtain assistance or service if you . The...
Warranty Information - Page 1
... to resolve
the problem after checking "Troubleshooting," additional help you obtain assistance or service if you on the product. Consumable parts are unable to correct the installation of God, improper installation, installation not in which it .
Some states and provinces do not allow limitations on major appliances with Whirlpool published installation instructions.
10. If you...
Dimension Guide - Page 1
... noise transfer.
■■ For closet installation, with a door, minimum ventilation openings in the top and bottom of installation and servicing.
■■ Additional clearances might be required for exhaust vent with elbow. DRYER DIMENSIONS
Models with riser
Electric Dryer
PRODUCT MODEL NUMBERS WED8000B, WED8100B, WED8500B, WED8900B
Models without riser
Side view Bottom view:
Back...
Installation Guide - Page 4
DRYER DIMENSIONS
Models with riser
You will be exposed to water, weather, or at end of automatic sensor cycles, resulting in longer drying times. See "Electrical Requirements."
■■ Floor must support dryer weight of installation and servicing; spacing for companion appliances and clearances for proper exhaust installation.
Check code requirements. Also consider weight of 1" (...
Installation Guide - Page 6
... posts the dryer was packed with to connect the exhaust vent. To avoid damaging floor, use a large flat piece of the riser. Foot is fully installed when bottom ... must be either green or bare. place under entire dryer.
Models without riser
Models with ring or spade terminals and UL listed strain relief. Prepare dryer for electrical connection and to avoid damaging the back of...
Installation Guide - Page 18
... the dryer's heater from each of your "Use and Care Guide." q Read "Dryer Use" in a running or "On" position. • Start button has been pushed firmly. • Dryer is first heated.
Remove the door assembly 1.
A
B
A B
A. If there is level. Steam models only:
q Be sure the water faucets are set in your tools. If you receive an L2 code, there...
Whirlpool WED8900BC Reviews
We have not received any reviews for Whirlpool yet.