Whirlpool KMHS120KPS Support and Manuals
Get Help and Manuals for this Whirlpool item
This item is in your list!
View All Support Options Below
Free Whirlpool KMHS120KPS manuals!
Problems with Whirlpool KMHS120KPS?
Ask a Question
Free Whirlpool KMHS120KPS manuals!
Problems with Whirlpool KMHS120KPS?
Ask a Question
Popular Whirlpool KMHS120KPS Manual Pages
Installation Instructions - Page 2
... the "Venting Design Specifications" section.
2 Washers (2) D. 3/16" toggle nuts (2) E. 1/4" x 2" lag screws (2)
■ Cardboard template (part of microwave oven)
C. Damper assembly (for wood or metal cabinet
■ Keyhole saw
■ Caulking gun and weatherproof caulking compound
■ Duct tape
Parts Needed
For information on reordering, see the "Replacement Parts" section. NOTE...
Installation Instructions - Page 3
... to it during the "Mark Rear Wall" and "Prepare Upper Cabinet" parts of the carton box. Set the cardboard template to the side and refer to Round Transition" illustration in the backside of installation.
12 1/2" (31,8 cm) 6 1/4" (15,9 cm)
5 3/4" (14,6 cm)
Installation Dimensions
NOTE: The grounded 3 prong outlet must be free of the carton...
Installation Instructions - Page 4
...circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
For all governing codes and ordinances.
WARNING: Improper use an adapter. Consult a qualified electrician or serviceman if ... these instructions can
result in death, fire, or electrical shock. SAVE THESE INSTRUCTIONS
4 Failure to whether the microwave oven is too short, have a qualified electrician or serviceman install an...
Installation Instructions - Page 5
... venting, changes must be made to the back of microwave oven, and set for recirculation installation. Lift blower motor out of the microwave oven. Damper plate
A. Blower Motor
5 Remove any remaining contents from the connector.
A
A.
INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model, the mounting plate may be in the foam packaging, or it...
Installation Instructions - Page 7
... cannot move. 11. Damper plate B. Exhaust port
IMPORTANT: If blower motor is not positioned with two screws removed in Step 1. Repeat Step 3 from "Wall Venting Installation Only." 5. Using diagonal wire cutting pliers, gently snip out the
rectangular vent covers on the damper plate at the perforations.
Screws
A. Check to its original...
Installation Instructions - Page 8
Support tabs F. Using a stud finder, locate the edges of the wall stud(s) within 6" (15.2 cm) of the vertical centerline
(see the "Mark Rear Wall" section), only recirculation or roof
venting installation can be done. No Wall Studs at End Holes Figure 1
No Wall Studs at End Holes Figure 4
B
D
B
A
A,D
A,D
A,D
E
E
E
E
C
C
C
C
F
F
A. See illustrations in "Possible Wall...
Installation Instructions - Page 9
... preferably two hole(s) through the marks made in steps 8 and 10.
12. A
Wall Venting Installation Only
A. Mark the centerline 3/8" (1 cm) down from the bottom edge of upper cabinet
3.
... edge of the cutout area. 14. Set the mounting plate aside.
Using a keyhole saw, cut out the venting cutout area. With the support tabs facing forward (see illustrations in the...
Installation Instructions - Page 10
... End Hole" in the "Drill Holes in Rear Wall" section.
2. Attach Mounting Plate to Wall
NOTE: Secure the mounting plate to open .
3. With the support tabs of "Installation for No Wall Studs at the other hole drilled in Step 3 of the mounting plate facing forward,
insert 3/16-24 x 3" round-head bolts through...
Installation Instructions - Page 11
...moves freely and opens fully. 2. Damper assembly C.
Power supply cord bushing
6. For Roof Venting Installation Only: 7. Prepare Upper Cabinet
1. NOTE:
■ If the wall behind the microwave oven ... Sheet metal screws
3. Make sure the 10" (25.4 cm) dimension from the rear wall to the thickest part of the rear wall (for wall venting only)
1.
Cut the 11⁄2" (3.8 cm) diameter hole at ...
Installation Instructions - Page 12
...is being handled. To avoid warping, wood filler blocks (installer to the microwave oven, do so can result in ...or more people, lift microwave oven off of mounting plate, and set aside on support tabs at most hardware stores.
■ Overtightening bolts may be ...thread power supply cord through 6. 11. Place a washer on your model, it may require bolts longer or shorter than 3" (7.6 cm). ...
Installation Instructions - Page 13
...vent)
13 Save Installation Instructions for future use an adapter. Vent B. Refer to the User Instructions for troubleshooting information.
Connect vent to follow these instructions can result in ... shown. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.
■ Check that a circuit breaker has not tripped. The installation is now...
Installation Instructions - Page 14
... equivalents are not provided with microwave hood combination.
■ We do not recommend using recirculation installation. Roof cap: 31⁄4" x 10" = 24 ft (8.3 x 25.4 cm = ...ft (8.3 x 25.4 cm = 3 m)
14 A
B
C
D
E
3" (7.6 cm)
F
A. VENTING DESIGN SPECIFICATIONS
This section is intended for the damper to open freely and fully. Rectangular-to-Round Transition NOTE: The minimum 3" ...
Installation Instructions - Page 15
...installing this microwave oven in the User Guide. Both numbers can be replaced, call us at our toll-free number or visit our website listed in the "Tools and Parts" section)
Filler Panel Kits:
A
A. Replacement Parts
If any of the installation... authorized dealer or service center. The total length of the system you need your dealer to be found on the model and serial number plate...
Whirlpool KMHS120KPS Reviews
Do you have an experience with the Whirlpool KMHS120KPS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Whirlpool yet.
Earn 750 points for your review!