Instruction Manual
Page 2
...over edge of experience and knowledge. 2 W hen blending hot liquids, completely remove the stopper in the cover before turning on or taking off parts, and before putting on the blender. T his appliance is dropped or damaged in use outdoors. 8. T he use by the appliance manufacturer... may be used only when the blender is not running. 10. Handle carefully. 11. K eep hands and utensils out of container while blending to prevent the possibility of severe personal injury and/or damage to the nearest authorized service facility for use of attachments, ...
...over edge of experience and knowledge. 2 W hen blending hot liquids, completely remove the stopper in the cover before turning on or taking off parts, and before putting on the blender. T his appliance is dropped or damaged in use outdoors. 8. T he use by the appliance manufacturer... may be used only when the blender is not running. 10. Handle carefully. 11. K eep hands and utensils out of container while blending to prevent the possibility of severe personal injury and/or damage to the nearest authorized service facility for use of attachments, ...
Instruction Manual
Page 12
... lubricated and sealed at the factory and do not require any way. 12 Replace these parts if they become worn or loose, or are 100˚F (38˚C) or hotter. • Always start blending on lowest speed setting, then progress to ... further lubrication. 2. Reduce amounts of material processed to less than the full 4-liter capacity when working with viscous or fibrous materials. 3. When cleaning exterior of container, keep it in normal upright operating position to desired speed. • Never stand directly over blender when it is being started or while it is...
... lubricated and sealed at the factory and do not require any way. 12 Replace these parts if they become worn or loose, or are 100˚F (38˚C) or hotter. • Always start blending on lowest speed setting, then progress to ... further lubrication. 2. Reduce amounts of material processed to less than the full 4-liter capacity when working with viscous or fibrous materials. 3. When cleaning exterior of container, keep it in normal upright operating position to desired speed. • Never stand directly over blender when it is being started or while it is...
Instruction Manual
Page 15
... run on motor base, and running into motor base by wringing all parts to air-dry. The Waring Commercial Blender ball-bearing motor requires no greasing or oiling. When operating with sanitizing solution. 2. If using the spigot. Do not rinse container, spigot assembly, rubber insert, lid, or lid insert after sanitizing is completed...
... run on motor base, and running into motor base by wringing all parts to air-dry. The Waring Commercial Blender ball-bearing motor requires no greasing or oiling. When operating with sanitizing solution. 2. If using the spigot. Do not rinse container, spigot assembly, rubber insert, lid, or lid insert after sanitizing is completed...
Instruction Manual
Page 16
...Waring® Commercial Blender to be sterilized without injury to loads in materials or workmanship, provided the product is to 70 foot-pounds torque) when reassembling container. Power Supply Cord - The stainless steel container can be free from defects in material and workmanship for conditions requiring replacement. When any part... which, upon our examination, is defective in excess of the container blade assembly, socket head shaft and shaft seals is therefore recommended that ...
...Waring® Commercial Blender to be sterilized without injury to loads in materials or workmanship, provided the product is to 70 foot-pounds torque) when reassembling container. Power Supply Cord - The stainless steel container can be free from defects in material and workmanship for conditions requiring replacement. When any part... which, upon our examination, is defective in excess of the container blade assembly, socket head shaft and shaft seals is therefore recommended that ...
Parts List and Exploded Diagram
Page 1
... Blending Assembly (replaces 502493 & 502975) (limited quantities available) 018397 - Montysko Revised October 31, 2012 Approved 10/31/12 Page 1 of 4 Container with Hot Blending Lid CBC15 Calico Label /marked for deletion LBC15 Laboratory Blender 19 20 11 26 21 12 22 502977 13 27 12 14 ...16 15 28 23 older units/ CB15-CB15DB-CB15S 29 current production/ LBC15 17 Parts to old 502493 30 Blending Assembly different from new Assembly 502235 - O Ring 023903 - OPEN LOCK 1 LOCK OPEN OPEN ...
... Blending Assembly (replaces 502493 & 502975) (limited quantities available) 018397 - Montysko Revised October 31, 2012 Approved 10/31/12 Page 1 of 4 Container with Hot Blending Lid CBC15 Calico Label /marked for deletion LBC15 Laboratory Blender 19 20 11 26 21 12 22 502977 13 27 12 14 ...16 15 28 23 older units/ CB15-CB15DB-CB15S 29 current production/ LBC15 17 Parts to old 502493 30 Blending Assembly different from new Assembly 502235 - O Ring 023903 - OPEN LOCK 1 LOCK OPEN OPEN ...
Parts List and Exploded Diagram
Page 3
... Gasket for container base Container Support (container base) Lock Nut Coupling Jar Pad Revised October 31, 2012 Page 3 of 4 Catalog/Model CB15 CB15DB CB15S CBC15 LBC15 Illustration # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Part # 024000 ...026496 023998 002972 027581 027683 018389 027582 018390 023934 004946 018386 023926 023907 023927 023906 023933 025817 028530 028226 013470 013469 017442 026496 008791 502773 023909 502977 004949 025571 012008 502696 025871 Waring Factory Service Center 314 Ella T.
... Gasket for container base Container Support (container base) Lock Nut Coupling Jar Pad Revised October 31, 2012 Page 3 of 4 Catalog/Model CB15 CB15DB CB15S CBC15 LBC15 Illustration # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Part # 024000 ...026496 023998 002972 027581 027683 018389 027582 018390 023934 004946 018386 023926 023907 023927 023906 023933 025817 028530 028226 013470 013469 017442 026496 008791 502773 023909 502977 004949 025571 012008 502696 025871 Waring Factory Service Center 314 Ella T.