Owner Manual
Page 5
... Start Safe-lock 22 Disabling Remote Start 22 Advanced Start 22 Manual Transmission Start (MTS mode 23 Turbo Timer Mode 24 Remote Start Faults 25 Remote and System Operations 26 Passive Arming 26 Auto Re-arming 26 Valet Mode 27 Power Save 27 Rapid Resume 27 Car Select 27 System Expansion Options 28 Battery...
... Start Safe-lock 22 Disabling Remote Start 22 Advanced Start 22 Manual Transmission Start (MTS mode 23 Turbo Timer Mode 24 Remote Start Faults 25 Remote and System Operations 26 Passive Arming 26 Auto Re-arming 26 Valet Mode 27 Power Save 27 Rapid Resume 27 Car Select 27 System Expansion Options 28 Battery...
Owner Manual
Page 8
s The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation. * See Remote and System Operations section for details. ** See Alarm Features for details. © 2010 Directed Electronics. All rights reserved. 5 It consists of the front windshield. Control Center Control button Status LED Antenna The Control Center, typically located on the upper part of : s The In-vehicle system antenna. s The Status LED, as a visual indicator of the system's status.
s The Control button, for placing the system into Valet Mode* and to perform the Emergency Override** operation. * See Remote and System Operations section for details. ** See Alarm Features for details. © 2010 Directed Electronics. All rights reserved. 5 It consists of the front windshield. Control Center Control button Status LED Antenna The Control Center, typically located on the upper part of : s The In-vehicle system antenna. s The Status LED, as a visual indicator of the system's status.
Owner Manual
Page 11
... The alarm Arms (or Locks in Valet) and, after 2 seconds, sounds the siren and flashes the parking lights. Disarm Press and release The alarm disarms, doors unlock (if connected), and the siren chirps and parking lights flash twice. Exit Valet mode to stop the output. All rights ...reserved. If Valet mode* is On, the doors lock without siren chirps, the alarm is detected the siren chirps once again and the control...
... The alarm Arms (or Locks in Valet) and, after 2 seconds, sounds the siren and flashes the parking lights. Disarm Press and release The alarm disarms, doors unlock (if connected), and the siren chirps and parking lights flash twice. Exit Valet mode to stop the output. All rights ...reserved. If Valet mode* is On, the doors lock without siren chirps, the alarm is detected the siren chirps once again and the control...
Owner Manual
Page 14
... to turn Sensor Bypass Off. Sensors will not be activated for any time to indicate Level 2. The transmit LED illuminates in sets of impact. Remote Valet Press and release Enters (or if On, exits) Valet Mode.
... to turn Sensor Bypass Off. Sensors will not be activated for any time to indicate Level 2. The transmit LED illuminates in sets of impact. Remote Valet Press and release Enters (or if On, exits) Valet Mode.
Owner Manual
Page 22
... lights for 3 seconds. All rights reserved. 19 Note As a precaution, if programmed for Passive Arming or Auto re-arming the system should be placed into Valet Mode until a remote is then monitored normally. Should a faulty zone self correct (dome light turns off) it becomes active and is available .
... lights for 3 seconds. All rights reserved. 19 Note As a precaution, if programmed for Passive Arming or Auto re-arming the system should be placed into Valet Mode until a remote is then monitored normally. Should a faulty zone self correct (dome light turns off) it becomes active and is available .
Owner Manual
Page 30
...mechanic or thief, the system will resume the state it was in at the time of the command buttons. © 2010 Directed Electronics. When Valet mode is On the LED turns off . Rapid Resume If power is 1 or 2, release the button for Car Select or continue to manually enter...after 24 hours. Release the button, then press and release while the LED flashes continue to turn on). Valet Mode Valet mode can be performed by performing the Remote Valet command or manually using the vehicle key and the control button. Immediately press and release the control button once 3. Use...
...mechanic or thief, the system will resume the state it was in at the time of the command buttons. © 2010 Directed Electronics. When Valet mode is On the LED turns off . Rapid Resume If power is 1 or 2, release the button for Car Select or continue to manually enter...after 24 hours. Release the button, then press and release while the LED flashes continue to turn on). Valet Mode Valet mode can be performed by performing the Remote Valet command or manually using the vehicle key and the control button. Immediately press and release the control button once 3. Use...