Viper 5104 Support Question
Viper 5104 Support Question
Find answers below for this question about Viper 5104.Need a Viper 5104 manual? We have 1 online manual for this item!
Current Answers
Related Viper 5104 Manual Pages
Owner Manual - Page 4
... 10 Silent Arm 10 Runtime Reset 10 AUX 1 10 Advanced Commands: (Level 2 11 Sensor Bypass 11 Remote Valet 11 Timer Start 12 AUX 2 12 Advanced Commands: (Level 3 13 Sensor Silent Arm 13 Smart Start 13...Configuration 15 Remote Programming 15 Remote Pairing 15 Remote Features 16 Sensor Adjust 17 Alarm Features 18 Normal Arm Protection 18 Sensor Silent Arm protection 18 Sensor Warn-...
Owner Manual - Page 5
... Remote Start Faults 25 Remote and System Operations 26 Passive Arming 26 Auto Re-arming 26 Valet Mode 27 Power Save 27 Rapid Resume 27 Car Select 27 System Expansion Options 28 Battery Information 29 Low Battery Alerts 29 Battery Replacement 29 Battery Disposal 30 Patent Information 30 Glossary of Terms ...
Owner Manual - Page 8
s The Control button, for placing the system into Valet Mode* and
to perform the Emergency Override** operation.
* See Remote and System Operations section for details. ** See Alarm Features for details.
© 2010 Directed Electronics. Control Center
Control button
Status LED
Antenna
The Control Center, typically located on the upper part of :
s The ...
Owner Manual - Page 11
... Directed Electronics. To Arm and Panic Press and hold The alarm Arms (or Locks in Valet) and, after 2 seconds, sounds the siren and flashes the parking lights.
Exit Valet mode to stop the output. Basic Commands (Direct Access)
Arm
Press and release
The alarm arms, doors lock (if connected), and the siren chirps and...
Owner Manual - Page 14
... Bypass. Note System needs to be confirmed as follows: s Warn-away bypass: The Parking lights flash 2 times. Remote Valet
Press and release
Enters (or if On, exits) Valet Mode. All rights reserved.
11 Sensors will incrementally bypass sensor operations and be armed to turn Sensor Bypass Off.
Perform arm command any...
Owner Manual - Page 16
...AUX 3
Press and release AUX Activates (or if On, deactivates) the Aux 3 output.
* See Alarm Features for more details.
© 2010 Directed Electronics.
The parking lights flash quickly five... Start Features for Off. All rights reserved.
13 The transmit LED illuminates in progress. Car finder
Press and release The siren emits one long chirp and the parking lights ...
Owner Manual - Page 19
...
* Indicates default setting. Car 2 Off *
Keypad Lock
Options: Off, Auto
When Off, the buttons do not lock and always perform a command when pressed. Press and hold the button for pairing: 6. Enter programming to pair. 8.
Remote Features
From the main menu, press the button to access the remote operation features, 2 transmit LED fl...
Owner Manual - Page 20
When set to avoid unintended alarm triggers; All rights reserved.
17 See Car Select (under Remote and System Operations) for detail on using a remote... sensor adjustments.
© 2010 Directed Electronics. it is used for sensor adjustment, to On the Car Select feature is enabled. Car 2
Options: Off, On
The remote controls can control two systems independently. It will not transmit ...
Owner Manual - Page 22
...the system should be placed into Valet Mode until a remote is 1 press). 3. Faulty zones (usually caused by remote command the system runs a status check of the alarm trigger zones.
Press the control ...off) it becomes active and is disarmed. All rights reserved.
19 Full Trigger output
An alarm Full Trigger will sound the siren and flash the parking lights for 3 seconds. ...
Owner Manual - Page 24
... for the programmed runtime.
4. Remote Start Features
Pit Stop Mode
To exit vehicle with engine running
The system keeps the engine... and release the foot brake.
2. Exit the vehicle and arm the alarm. The vehicle is ready to drive.
© 2010 Directed Electronics. To..., the remote start then turns off. 3. Disarm the system and enter the vehicle, do not step on .
3. Press the button, the...
Owner Manual - Page 25
... the Off position. Timer Start and Smart Start will repeat as many times as set
22
© 2010 Directed Electronics. s For manual transmission vehicles MTS mode must be enabled
before Timer Start or Smart Start can be enabled at any given
time. If remote start is attempted while Off, the engine...
Owner Manual - Page 26
... Timer Start is properly set the parking brake and leave the engine running after arming), open the driver door.
2.
For Pit Stop or Turbo Timer mode (to perform this step.
3. Smart Start operation Smart Start uses the settings for Timer Start in addition to temperature and battery level to automatically start...
Owner Manual - Page 27
...the optional dash mounted activation button or perform the
Timer Mode command. 3. Turn Off and remove the key from the ignition switch, the engine remains running for... the Turbo Mode runtime. Exit the vehicle, close all the doors and arm the system. 6. Turbo Timer Mode
The system keeps the engine running . 6. With the engine running...
Owner Manual - Page 28
...
© 2010 Directed Electronics. Flashes * 5 6 7
Possible Fault Brake on Disarm or reset alarm
* Refers to the table below for the command type and parking light flashes that will not... performing Timer Start or Smart Start command
Toggle Switch off
Alarm is triggered
Solution Release foot brake Close hood Enable MTS mode
Check all Solutions
Turn switch on
Hood open
After performing ...
Owner Manual - Page 29
... then chirps once. Anytime before the system arms you can be turned on by remote, the alarm automatically re-arms itself (and locks the doors if programmed on) in case of entry to...channel outputs if programmed to temporarily bypass the Passive arming operation for one -time bypass is not entered after disarming by remote.
Auto Re-arming*
Auto re-arm ensures the vehicle stays protected if...
Owner Manual - Page 30
... period.
All rights reserved.
27 Valet Mode
Valet mode can be performed by pressing one of disconnection, when power is turned off. When entered, the alarm functions are defeated while the convenience ...while the LED flashes continue to manually enter and exit Valet Mode: 1. Car Select
Car 2 remote control option must first be entered and exited by a mechanic or thief, ...
Owner Manual - Page 31
... time of time the siren sounds can be configured to match the remote users preferences.
Alarm output duration * The length of installation. See Owner Recognition for details. System Expansion Options
Controlling two vehicles (Car Select) The remote controls can all be custom set for each vehicle that prefer a custom silent...
Owner Manual - Page 34
...
A hand-held, remote control which monitors your vehicle and controls all of your system. It is used to enter or exit Valet Mode.
© 2010 Directed Electronics.
Status LED
A light used to override (disarm) the alarm when a remote is usually located at the top of your system. It houses the microprocessor which operates the...
Owner Manual - Page 37
... has not been properly installed. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. (1) Never remotely start ...vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start while the car is the responsibility of the vehicle periodically checked, wherein the vehicle must be performed by...
Owner Manual - Page 38
..., soft or hard top with this product. Please take care to be in such vehicles may pose certain risk. GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. Installation in strict accordance with a manual transmission.
This product should not be performed by an authorized Directed dealer.
This product is not designed...
Similar Questions
Bought Suv No Crank No Start Find Out It Has Viper 350hv Alarm How. To Disable
(Posted by jolivas18 10 months ago)
I Want To Run A System Reset/restart On My Alarm - Viper 5704v.
i think i have to put the alarm in valet mode to make sure that the remote start feature is not affe...
i think i have to put the alarm in valet mode to make sure that the remote start feature is not affe...
(Posted by rdmutch 8 years ago)
Viper Car Alarm
my remote will not /unlock the door or enable the ignition
my remote will not /unlock the door or enable the ignition
(Posted by jbggkm 9 years ago)
Silent Mode
is there a way to put my 3105v viper car alarm in silent mode when arming my system
is there a way to put my 3105v viper car alarm in silent mode when arming my system
(Posted by maldi20s 10 years ago)
