Via EPIA-ML6000EAG - VIA Motherboard - Mini ITX Support and Manuals
Get Help and Manuals for this VIA Technologies item
View All Support Options Below
Free Via EPIA-ML6000EAG manuals!
Problems with Via EPIA-ML6000EAG?
Ask a Question
Free Via EPIA-ML6000EAG manuals!
Problems with Via EPIA-ML6000EAG?
Ask a Question
Popular Via EPIA-ML6000EAG Manual Pages
User Manual - Page 1
User's Manual
EPIA-ML Mini-ITX Mainboard
Version 1.0 July 7, 2004
User Manual - Page 4
... Replace only with the same or equivalent type recommended by a
service personnel: • The power cord or plug is incorrectly replaced. Safety Instructions
1. Keep this equipment on a reliable flat surface before setting it... the equipment to moisture • The equipment has not work according
to User's Manual. • The equipment has dropped and damaged • If the equipment has ...
User Manual - Page 6
... Chipset Features 3-11 Integrated Peripherals 3-13 Power Management Setup 3-17 PNP / PCI Configurations 3-22 PC Health Status 3-25 Frequency / Voltage Control 3-26 Load Fail-Safe Defaults 3-28 Load Optimized Defaults 3-29 Set Supervisor / User Password 3-30 Save & Exit Setup 3-32 Exit Without Saving 3-33
Chapter 4: Driver Installation 4-1
Driver Utilities 4-2 CD Content 4-3
vi
User Manual - Page 7
... Layout
1-4
Back Panel Ports
1-5
Slots
1-5
Connectors / Jumpers
1-6
1-1
as part of FlexATX mainboard form factor. Chapter
Specifications
The ultra-compact and highly intergrated VIA EPIA-ML Mini-ITX Mainboard is the smallest form factor mainboard specification available today, developed by VIA Technologies, Inc. The mainboard comes with an embedded VIA Processor, boasting ultra...
User Manual - Page 23
... speakers to Smart 5.1 6-channel audio output.
PS2_MS
RJ45
PS2_KB
VGA Out
USB
Parallel (LPT1) COM1
Line-In Line-Out Microphone
2-11 After completing the previous settings, you need to connect your desktop after installing the audio driver. You can be switched to the audio jacks as shown below.
User Manual - Page 39
...you select Manual, make sure the
information provided is from your drive must match with the drive table. Number of the landing zone. The settings are Mode 0/1/2/3/4, Auto. Number of the storage device. AwardBIOS CMOS Setup Utility ... F6: Fail-Safe Defaults
ESC: Exit F1: General F7: Optimized Defaults
Help
The specifications of your hard disk vendor or system manufacturer.
User Manual - Page 43
...: Fail-Safe Defaults
ESC: Exit F1: General F7: Optimized Defaults
Help
WARNING: Do not change these settings unless you are forwarded to PCI POST Write Select Display Device Panel Type CPU Direct Access FB
Phoenix - Settings: 4MB, 8MB, 16MB, 32MB, 64MB, 128MB, and 256MB
AGP Mode (Internal)
This mainboard supports the AGP 4x interface.
User Manual - Page 47
...operate the onboard parallel port as Standard Parallel Port, choose SPP. Settings:
Port 1 2
Settings
Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Disabled 3F8/IRQ4...Set the base I/O port address and IRQ for the onboard serial port A/serial
port B. Settings: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7
Parallel Port Mode Set the parallel port mode. BIOS Setup
SuperIO Device
Press Enter to support...
User Manual - Page 53
... interrupt itself and perform the service required by causing an IRQ to I /O device needs to gain attention of the specified IRQ line. Settings: Off, On
IRQ3~IRQ15 ... from power saving modes if activity is on. These fields are system resources allocated to occur. AwardBIOS CMOS Setup Utility IRQs Activities
[ON] [Disabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [Disabled] ...
User Manual - Page 55
Settings: Disabled and Enabled
3-23 Settings: Auto (ESCD) and Manual
Assign IRQ For VGA/USB
Assign IRQ for VGA and USB devices. BIOS Setup
Resource Controlled By
The BIOS can automatically configure all the boot and Plug and Play compatible devices. Choose Auto(ESCD) if unsure, the BIOS will automatically assign IRQ, DMA and memory base address fields.
User Manual - Page 56
...Settings:
PCI Device Reserved
For Plug & Play compatible devices designed for users to
Phoenix - AwardBIOS CMOS Setup... Utility IRQ Resources
[PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device] [PCI Device]
Item Help
Menu Level
Legacy ISA for devices compliant with the original PC AT bus specification... By is set each IRQ ...
User Manual - Page 58
... Defaults
Help
DRAM Clock
The chipset supports synchronous and asynchronous mode between host clock and DRAM clock frequency. Generally, a lower setting will improve the performance of your system becomes less stable, you install new memory that has a different performance rating than the original modules. Settings: 2, 2.5
3-26 AwardBIOS CMOS Setup Utility Frequency / Voltage Control
DRAM...
User Manual - Page 59
... Command, 1T
Command
Spread Spectrum
When the mainboard's clock generator pulses, the extreme values (spikes) of the SDRAM interface. Settings: Disabled, 2 Bank, 4 Bank
Precharge to Active (Trp)
This field controls the length of SDRAM to Manual. This field is only available when DRAM Timing is set to Manual. Settings:
2T, 3T
DRAM Command Rate
This field...
User Manual - Page 69
... CD are:
• VIA 4in1 Drivers: Contains VIA ATAPI Vendor Support Driver (enables the performance enhancing bus mastering functions on ATAcapable Hard Disk Drives and ensures IDE device compatibility), AGP VxD Driver (provides service routines to your VGA driver and interface directly to hardware, providing fast graphical access), IRQ Routing Miniport Driver (sets the system's PCI IRQ routing...
Operating Guide - Page 16
...Series Operating Guide
VIA EPIA ML-Series Microsoft and Linux Driver Support
Microsoft Driver Support
VIA EPIA ML series offers full support for latest updates on VIA Arena, or through your specific needs.
Linux Driver Support
VIA EPIA ML mainboards have a very high degree of Microsoft operating systems.
For standard operating systems, Windows 98/Me/2000/XP latest drivers downloads can work...
Via EPIA-ML6000EAG Reviews
We have not received any reviews for Via yet.