Via EPIA-EN12000EG - VIA Motherboard - Mini ITX Support and Manuals
Get Help and Manuals for this VIA Technologies item
View All Support Options Below
Free Via EPIA-EN12000EG manuals!
Problems with Via EPIA-EN12000EG?
Ask a Question
Free Via EPIA-EN12000EG manuals!
Problems with Via EPIA-EN12000EG?
Ask a Question
Popular Via EPIA-EN12000EG Manual Pages
User Manual - Page 6
... ii Chapter 1 1
Specifications 1 Mainboard Specifications 2 Mainboard Layout 5 Back Panel Layout 6 Back Panel Ports 7 Slots 7 Onboard Connectors 8 Onboard Jumpers 8 Chapter 2 9 Installation 9 CPU 10 Memory Module Installation 12 Connecting the Power Supply 13 Back Panel Ports 14 Connectors 17 Jumpers 25 Slots 27 Chapter 3 29 BIOS Setup 29 Entering Setup 30 Control Keys 31...
User Manual - Page 21
Installation
CONNECTING THE POWER SUPPLY
The VIA EPIA-EN Mini-ITX mainboard supports a conventional ATX power supply for the power system. ATX 20-Pin Power Connector To connect the ATX power supply, make sure that no damage will be caused. Pin Signal
1
+3.3V
2
+3.3V
3
GND
4
+5V
5
GND
6
+5V
7
GND
8
Power Good
9
+5V Standby
10
+12V
11
+3.3V
12
-12V
13
GND
14
Power ...
User Manual - Page 24
.../Right) Center/Sub-woofer
16 Chapter 2
Audio Port:
The Line-Out jack is for connecting to setup the 6-channel system.
You can be switched to the 3-jack connectors on your desktop after installing the audio driver. Shown below are the corresponding connections to external speakers or headphones. Note: The audio ports can enable...
User Manual - Page 33
... will cause system boot failure. Clear CMOS: CLEAR_CMOS
The onboard CMOS RAM stores system configuration data and has an
onboard battery power supply. Return the jumper to change the settings of the mainboard functions using the jumpers. Removing the cap will damage the mainboard. To reset the CMOS settings, set the jumper
on CLEAR_CMOS jumper default position.
User Manual - Page 35
... A#
27
Read the documentation for the expansion card if any changes to insert PCI expansion card. When adding or removing expansion card, unplug first the power supply. SLOTS
Installation
Peripheral Component Interconnect: PCI The PCI slot allows you to the system are necessary.
User Manual - Page 48
Setting Setup
System
Description Password prompt appears only when end users try to run BIOS Setup
APIC Mode Enables APIC (Advanced Programmable Interrupt Controller) functionality. Settings: [250, 500, 750, 1000]
Security Option Selects whether the password is powered on and when end users try to repeat the signal from a depressed key. Settings: [Enabled, Disabled]
MPS Variation ...
User Manual - Page 73
... frequency. Generally, a lower setting will improve the performance of your system becomes less stable, you install new memory that has a different performance rating than the original modules.
This field is only available when "DRAM Timing" is not recommended unless you should change it takes for the memory module to "Manual". AwardBIOS CMOS Setup Utility Frequency / Voltage...
User Manual - Page 75
..., 4T, 5T]
BIOS Setup
Read to Precharge (Trptp) Settings: [2T, 3T]
Write to Read CMD (Twtr) Settings: [1T/2T, 2T/3T]
Write Recovery Time (Twr) Settings: [2T, 3T, 4T, 5T]
DRAM Command Rate This field is set to "Manual". Settings: [2T Command, 1T Command]
Note: Some memory modules may not be able to handle lower settings. The Spread Spectrum function...
User Manual - Page 78
... Supervisor Password
Power Management Setup
Set User Password
PnP / PCI Configurations
Load Optimized Defaults (SYa/Nv)e?& NExit Setup
PC Health Status
Exit Without Saving
ESC : Quit
F9 : Menu in BIOS
F10 : Save & Exit Setup
: Select Item
Load Optimized Defaults
This option is for restoring all the default optimized BIOS settings. The default optimized values are set by the mainboard...
User Manual - Page 85
... on the "Start" button and select "Run..." Then type: "D:\Setup.exe". The driver utilities and software menu screen should run automatically, click on the screen. If the CD does not run automatically after closing the CD-ROM or DVD-ROM drive. Driver Installation
Running the Driver Utilities CD To start using the CD, insert the...
User Manual - Page 86
... Vendor Support Driver (enables the performance enhancing bus mastering functions on ATA-capable Hard Disk Drives and ensures IDE device compatibility), AGP VxD Driver (provides service routines to your VGA driver and interface directly to hardware, providing fast graphical access), IRQ Routing Miniport Driver (sets the system's PCI IRQ routing sequence) and VIA INF Driver (enables the VIA Power...
Operation Guide - Page 2
... EPIA EN Processor SKUs ...4 VIA CN700 Chipset Overview ...5 VIA EPIA EN-Series I/O Back Panel Layout...6 VIA EPIA EN-Series Layout Diagram & Mounting Holes ...7 VIA EPIA EN-Series Layout Diagram & Height Distribution...8 Power Consumption...9
VIA EPIA EN12000E...9 VIA EPIA EN15000 ...10 Power Specifications ...12 VIA EPIA EN-Series Microsoft and Linux Driver Support ...13 MICROSOFT DRIVER SUPPORT...
Operation Guide - Page 3
... power and secure x86 processor platforms.
January 18, 2012
- 1 - With the sizable memory bandwidth of DDR2 533MHz SDRAM DIMM and the high data transfer speeds of ATA-133 and further enhanced by support of 8Channel AC'97 codec for expandability options.
EPIA EN-Series Operating Guide
VIA EPIA EN-Series Overview
The VIA EPIA EN-Series Mini-ITX Mainboard...
Operation Guide - Page 5
... Guide
VIA EPIA EN-Series Specifications
Model Name
EPIA EN15000
EPIA EN12000E
Processor
VIA C7 1.5GHz NanoBGA2
VIA Eden 1.2GHz NanoBGA2
Chipset
- VIA FliteDeck™ Suite MissionControl-H/W Monitoring, Remote SNMP Management FlashPort-Live BIOS Flash
SysProbe-Live DMI Browser
System Monitoring & Management
- VIA VT1618 8-channel AC'97 Codec
Onboard TV Out
- System power...
Operation Guide - Page 14
Version 1.21 EPIA EN-Series Operating Guide
Power Specifications
The EPIA EN utilizes an industry standard 20-pin ATX main connector to the EPIA EN platform's ultra low power requirements a 90 - 120 Watt ATX power supply is ample for even the heaviest of multimedia system applications.
1
11
2
12
3
13
4
14
5
6... Gnd Gnd NC +5V +5V
January 18, 2012
- 12 -
Due to the power supply.
Via EPIA-EN12000EG Reviews
We have not received any reviews for Via yet.