Operation Manual
Page 7
...minimum). fill: 20 oz. (0.59 l), type: SAE 30 detergent oil with fresh unleaded regular gasoline from igniting the gasoline, place the container and/or mower directly on the ground before filling, not in an approved fuel container, out of the reach of SF, SG, SH, SJ, SL, or higher...others. • To prevent a static charge from a major name-brand service station (Figure 8). Adjust the cutting height as the rear wheels (Figure 10). 7 Set the front wheels to the Full mark on the dipstick, slowly pour oil into contact with gasoline less than 10% ethanol because the fuel system ...
...minimum). fill: 20 oz. (0.59 l), type: SAE 30 detergent oil with fresh unleaded regular gasoline from igniting the gasoline, place the container and/or mower directly on the ground before filling, not in an approved fuel container, out of the reach of SF, SG, SH, SJ, SL, or higher...others. • To prevent a static charge from a major name-brand service station (Figure 8). Adjust the cutting height as the rear wheels (Figure 10). 7 Set the front wheels to the Full mark on the dipstick, slowly pour oil into contact with gasoline less than 10% ethanol because the fuel system ...
Operation Manual
Page 13
...pace while mowing. - Cut the grass more of sticks, stones, wire, branches, and other debris that the blade could hit. • Avoid striking solid objects with each pass. - Set the cutting height on the front wheels... local fire warnings, and keep the mower free of cutting a full swath with the blade. Walk at a time. Operating Tips General ...when necessary with a Toro replacement blade. Replace the blade or have it is too long, the mower may plug and cause...grass is unsatisfactory, try one notch lower than the rear wheels. Refer to stall. Figure 22 Removing the Side ...
...pace while mowing. - Cut the grass more of sticks, stones, wire, branches, and other debris that the blade could hit. • Avoid striking solid objects with each pass. - Set the cutting height on the front wheels... local fire warnings, and keep the mower free of cutting a full swath with the blade. Walk at a time. Operating Tips General ...when necessary with a Toro replacement blade. Replace the blade or have it is too long, the mower may plug and cause...grass is unsatisfactory, try one notch lower than the rear wheels. Refer to stall. Figure 22 Removing the Side ...
Operation Manual
Page 14
set the front cutting height one pass over the leaves. • If there are more than the rear cutting height. • Slow down your mowing speed if the mower does not cut leaf cover. You may need to make more than one or two notches higher than 5 inches (13 cm) of the lawn shows through the cut the leaves finely enough. 14 Cutting Leaves • After cutting the lawn, ensure that half of leaves on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at 2-1/2 inches (64 mm).
set the front cutting height one pass over the leaves. • If there are more than the rear cutting height. • Slow down your mowing speed if the mower does not cut leaf cover. You may need to make more than one or two notches higher than 5 inches (13 cm) of the lawn shows through the cut the leaves finely enough. 14 Cutting Leaves • After cutting the lawn, ensure that half of leaves on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at 2-1/2 inches (64 mm).
Parts Catalog
Page 2
...forming PRH: phillips round head PTH: phillips truss head PTO: power-take-off RH: right hand ROPS: roll-over protection system RRB: rear roller brush SFH: slotted fillister head SHH: slotted hex head... SHWH: slotted hex washer head SPH: slotted pan head SQH: square head SRH: slotted round head STD: standard TAP: self tapping TTH: torx truss head 2 List of Abbreviations AR: as required ASM: assembly BBC...37 are indicated. For example, a wheel assembly might be identified by reference number 6, the tire by 6:1, the valve by 6:2, and...
...forming PRH: phillips round head PTH: phillips truss head PTO: power-take-off RH: right hand ROPS: roll-over protection system RRB: rear roller brush SFH: slotted fillister head SHH: slotted hex head... SHWH: slotted hex washer head SPH: slotted pan head SQH: square head SRH: slotted round head STD: standard TAP: self tapping TTH: torx truss head 2 List of Abbreviations AR: as required ASM: assembly BBC...37 are indicated. For example, a wheel assembly might be identified by reference number 6, the tire by 6:1, the valve by 6:2, and...
Parts Catalog
Page 3
Contents Deck, Side Chute and Rear Door Assembly 4 Rear Bag Assembly 5 Engine and Blade Assembly 6 Front Wheel and Height-of-Cut Assembly 7 Transmission and Rear Wheel Drive Assembly 8 Upper Handle Assembly 9 Upper Handle Component Assembly 10 Attachments and Accessories 11 © 2011-The Toro® Company Contact us at www.Toro.com. 8111 Lyndale Avenue South Bloomington, MN 55420 3 Printed in the USA. All Rights Reserved
Contents Deck, Side Chute and Rear Door Assembly 4 Rear Bag Assembly 5 Engine and Blade Assembly 6 Front Wheel and Height-of-Cut Assembly 7 Transmission and Rear Wheel Drive Assembly 8 Upper Handle Assembly 9 Upper Handle Component Assembly 10 Attachments and Accessories 11 © 2011-The Toro® Company Contact us at www.Toro.com. 8111 Lyndale Avenue South Bloomington, MN 55420 3 Printed in the USA. All Rights Reserved
Parts Catalog
Page 8
...Stepped 19 614650 2 Bolt-Shoulder 20 115-4695 2 8 Inch Wheel Gear ASM 21 115-8406 2 Anchor-Bag 22 105-9437 2 Screw-PPH 23 115-2893 1 Shield-Trailing 24 117-1092 2 Screw-PTH 3371-848A 8 C3 Transmission and Rear Wheel Drive Assembly Ref. Part Number Qty. Part Number Qty. Description ...1 114-7955-03 1 Plate-Rear, LH (HOC) 2 114-7956-03 1 Plate-Rear, RH (HOC) 3 322-3 4 Screw-HH 4 3296-29 4 Nut-Lock, NI 5 ...
...Stepped 19 614650 2 Bolt-Shoulder 20 115-4695 2 8 Inch Wheel Gear ASM 21 115-8406 2 Anchor-Bag 22 105-9437 2 Screw-PPH 23 115-2893 1 Shield-Trailing 24 117-1092 2 Screw-PTH 3371-848A 8 C3 Transmission and Rear Wheel Drive Assembly Ref. Part Number Qty. Part Number Qty. Description ...1 114-7955-03 1 Plate-Rear, LH (HOC) 2 114-7956-03 1 Plate-Rear, RH (HOC) 3 322-3 4 Screw-HH 4 3296-29 4 Nut-Lock, NI 5 ...