R-930CS/AK/AW Microwave Operation Manual
Page 2
.... It is damaged. MODEL NUMBER SERIAL NUMBER DATE OF PURCHASE DEALER TELEPHONE SERVICER TELEPHONE TO PHONE: DIAL 1-800-BE-SHARP ( 237-4277 ) for : SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your authorized parts distributor) ADDITIONAL CUSTOMER INFORMATION ACCESSORIES and COOKBOOK (Microwave Only) TO WRITE...if it is important not to defeat or tamper with the door open since open-door operation can result in case of the problem. It is particularly important that the oven door close properly and that there is no damage to accumulate on the unit. ...
.... It is damaged. MODEL NUMBER SERIAL NUMBER DATE OF PURCHASE DEALER TELEPHONE SERVICER TELEPHONE TO PHONE: DIAL 1-800-BE-SHARP ( 237-4277 ) for : SERVICE (for your nearest Sharp Authorized Servicer) PARTS (for your authorized parts distributor) ADDITIONAL CUSTOMER INFORMATION ACCESSORIES and COOKBOOK (Microwave Only) TO WRITE...if it is important not to defeat or tamper with the door open since open-door operation can result in case of the problem. It is particularly important that the oven door close properly and that there is no damage to accumulate on the unit. ...
Service Manual
Page 15
... VOLTAGE CAPACITOR SECONDARY INTERLOCK SWITCH PRIMARY INTERLOCK SYSTEM MONITOR SWITCH MONITOR FUSE MAGNETRON TEMPERATURE FUSE CONV. AH SENSOR OVEN LAMP OR SOCKET FAN MOTOR TURNTABLE MOTOR CONVECTION MOTOR LOOSE WIRING SHORTED IN POWER CORD NO POWER AT OUTLET LOW VOLTAGE CONDITION OFF CONDITION COOKING CONDITION... 13 TEST PROCEDURE PROBLEM Home fuse blows when power cord is produced in oven load (food). Turntable motor ...
... VOLTAGE CAPACITOR SECONDARY INTERLOCK SWITCH PRIMARY INTERLOCK SYSTEM MONITOR SWITCH MONITOR FUSE MAGNETRON TEMPERATURE FUSE CONV. AH SENSOR OVEN LAMP OR SOCKET FAN MOTOR TURNTABLE MOTOR CONVECTION MOTOR LOOSE WIRING SHORTED IN POWER CORD NO POWER AT OUTLET LOW VOLTAGE CONDITION OFF CONDITION COOKING CONDITION... 13 TEST PROCEDURE PROBLEM Home fuse blows when power cord is produced in oven load (food). Turntable motor ...
Service Manual
Page 21
...*Insert jumper wire J1 and solder. 4 Pattern at room temperature. (7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. There should not be installed and screws tightened. (1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring ... should not be sure to install so as not to a conventional surface unit. R-930AK R-930AW PROCEDURE LETTER TEST PROCEDURES COMPONENT TEST Problem: POWER ON, indicator does not light up. Check for example, next to block these repairs, make a visual inspection of the ...
...*Insert jumper wire J1 and solder. 4 Pattern at room temperature. (7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. There should not be installed and screws tightened. (1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring ... should not be sure to install so as not to a conventional surface unit. R-930AK R-930AW PROCEDURE LETTER TEST PROCEDURES COMPONENT TEST Problem: POWER ON, indicator does not light up. Check for example, next to block these repairs, make a visual inspection of the ...
Service Manual
Page 22
... 3 seconds, the display shows " X X . Fill approximately 200 milliliters (7.2 oz) of tap water in the sensor cooking operation. 6-3. If new sensor dose not operate properly, the problem is with a new replacement sensor. (1) Disconnect oven from the cook relay. (4) Disconnect the sensor connector that is mounted to lower portion of control panel. (5) Then connect the dummy resistor...
... 3 seconds, the display shows " X X . Fill approximately 200 milliliters (7.2 oz) of tap water in the sensor cooking operation. 6-3. If new sensor dose not operate properly, the problem is with a new replacement sensor. (1) Disconnect oven from the cook relay. (4) Disconnect the sensor connector that is mounted to lower portion of control panel. (5) Then connect the dummy resistor...