Sennheiser M 8 Support and Manuals
Get Help and Manuals for this Sennheiser item
View All Support Options Below
Free Sennheiser M 8 manuals!
Problems with Sennheiser M 8?
Ask a Question
Free Sennheiser M 8 manuals!
Problems with Sennheiser M 8?
Ask a Question
Popular Sennheiser M 8 Manual Pages
Instructions for Use - Page 25
... jacks - Master output level switchable from + 6 dBu to the application; Possibility to set up to couple two mixing consoles - Available with three steps - The essential features in all other professional fields, as well. Brief description of signal voltages up configurations specific to + 15 dBu - 1 kHz and 10 kHz reference tone generator - but...
Instructions for Use - Page 27
... 10 are disabled
when this
button depressed and monitor
selector switch 14 in the "post F"
setting the mute circuit
will be
self-locking, depending on
the model used. fect the footfall filter.
10
Treble, bass and mid-range
controls.
11 Control for infinite shifting of the effect
signal level.
5
Pre-listen button...
Instructions for Use - Page 34
...: greater than 1.5 kOhm Sensitivity: - 64 dBu to + 26 dBu depending on the settings of 1 and 2 at the input module
Talkback output, unbalanced; plug connector: 3-pin...+ AF 3 = - AF Impedance: approx. 10 kOhm Sensitivity: - 44 dBu to + 6 dBu, depending on the settings of 1 and 2 at 300 Ohm
Monitor outputs L and R;
Plug connector:
6.3 mm 0 phone jack.
plug connector: ...
Instructions for Use - Page 35
...specifications shown on an external battery or from ground. b. Release and remove the battery compartment cover (see fig. 1). Note: If more than 30 VDC is inadvertently applied, the power circuit will be disconnected.
2. Power supply
1.1 Battery operation (6- Install... isolated from the line supply, batteries which may be installed in the legend. The functions and wiring of the...
Instructions for Use - Page 36
...30 to units with the "MIC"/"LINE" slide switch 47, separately for Aux Send is used .
2. Set the fine gain adjustment 2 to provide the additional amplification required (0 to achieve the desired send level.
-...front of the input socket will be output as required, to branch off in the "post F" setting the Aux Send path will also be muted when mute switch 6 is to connect high-level ...
Instructions for Use - Page 37
... Hz). Note: The channel output is muted behind the fader so that it is still possible to pre- Set the footfall filter selector switch 8 in its
setting at the 80 Hz and 140 Hz switch settings, as the filter has a decreasing slope of the microphone being used, effective spurious noise suppression is
put...
Instructions for Use - Page 38
... L and R will be monitored or release the PPM push-button 26. quency. 4. Note: When the PPM push-button is depressed the monitor source set at its + 0 dB setting. 2. Use monitor selector switch 27 to select the source to
be displayed and monitored. 8. Put master fader 21 at monitor selector switch 27 will...
Instructions for Use - Page 39
... - 20 dB".
- 37 - Turn the "Gain" control 32 to the left stop. 3. Talkback module 1. Set the "Talkback volume" control 35 for the desired monitoring volume. 6. ting or, when an external microphone is connected, in the "OFF" setting. 5.
Set the volume control 37 for the desired volume. 4. Put source selector switch 36 in the...
Instructions for Use - Page 40
...an input module, monitor module or talkback module
Repair
Locate the defective module by pulling out the modules one at its center setting. The various operating conditions and their meanings:
...Blinking red
The operational voltage applied to indicate correct functioning. In this energy-saving setting not only the instrument illumination, but still sufficient for approx. 30 minutes of...
Instructions for Use - Page 41
...
8 .70
s6 •••ion,s7
l b ens
channel 5
channel
Sub-D 25-socket
Switch position shown: Channel fader in CO setting
Contact designations for fader switch
Switch position shown: Fader in CO setting
Connection example for channel 4 (seen from the connection side)
Red light with fader pushed up
024
*0 523 9 • I"nt...
Instructions for Use - Page 45
... modules:
approx. 15 kg
equipped with 8 channel modules:
approx. 18 kg
equipped with 12 channel modules:
approx. 23 kg
We reserve the right to alter specifications, in particular with regard to 16 kHz)
Line' Playback'
10 kOhm > 10 kOhm
Insert socket:
= 1 kOhm
Output impedances
Line output L/R:
< 40 Ohm (typ. 25 Ohm...
Sennheiser M 8 Reviews
We have not received any reviews for Sennheiser yet.