Seiko DPU-3445-30A-E Support and Manuals
Get Help and Manuals for this Seiko item
View All Support Options Below
Free Seiko DPU-3445-30A-E manuals!
Problems with Seiko DPU-3445-30A-E?
Ask a Question
Free Seiko DPU-3445-30A-E manuals!
Problems with Seiko DPU-3445-30A-E?
Ask a Question
Most Recent Seiko DPU-3445-30A-E Questions
Model Differences
What is the difference between a DPU-3445-20A and a DPU-3445-30A
What is the difference between a DPU-3445-20A and a DPU-3445-30A
(Posted by sagertd 7 years ago)
Smart Label Printer 440
Labels are loaded - but green light continues to flash.
Labels are loaded - but green light continues to flash.
(Posted by JanFullerJohnson 7 years ago)
Popular Seiko DPU-3445-30A-E Manual Pages
User Guide - Page 1
Seiko Instruments Inc. Keep this user's guide carefully before using the printer. USER'S GUIDE
Thermal Printer
DPU-3445-20
Read this user's guide in a place where it can be accessed quickly.
User Guide - Page 2
..., arithmetic, or listing errors. The information contained herein is a trademark of SII.
All other trademarks are the properties of DENSO INDUSTRIES INC. BHT Ir is a trademark of their respective companies.
SII reserves the right to make changes without the prior written approval of Seiko Instruments Inc. DPU-3445-20 THERMAL PRINTER USER'S GUIDE Document Number U00018388105 First...
User Guide - Page 4
... SETTING 16 7 CONNECTING TO THE HOST COMPUTER 22 8 RECHARGING THE BATTERY PACK 24 9 THERMAL HEAD MAINTENANCE 26 10 TROUBLESCHOOTING 27 11 SPECIFICATIONS 28 12 OPTIONS AND CONSUMABLE PARTS 29
For more detailed technical information on pages 2 to the DPU-3445-20 Thermal Printer. INTRODUCTION
User's Guide applies to 6 carefully before using the printer. Also read the instruction manuals...
User Guide - Page 15
... of Parts)
before setting the cut sheet.
(3) Insert a cut sheet with its printable
surface facing down the FEED button. Place a cut sheet into the slot straight.
HINT • Marks for roll paper.
When the printer detects the mark, it automatically.
(5) To discharge the paper from that is being loaded. The POWER and ERROR lamps...
User Guide - Page 17
... cover is changed, the function setting must be used with the paper holder installed. When the paper type is
open.
HINT • To remove the paper, turn the printer off and open the platen cover. Turn the printer over again.
(6) Turn the printer over , and open the paper cover. The ERROR lamp should be removed from...
User Guide - Page 18
... the printer, perform test printing.
5 TEST PRINTING
After loading paper in the printer and the printer is off . (2) Press the POWER and FEED buttons at the same time. "DPU-3445 " "[Ver Copyright (C) : SII
. . .
(4) After test printing, the printer goes into standby mode.
- 15 - If the paper
is not loaded, load the paper as instructed in Section 4, Paper Setting, and...
User Guide - Page 19
... the message shown at the same time. HINT • If an error occurs in the printer.
This manual describes how to set functions by entering commands. HINT • See the Technical Reference for details. • If you to see the printer's transmission status. The settings are stored in the software DIP switches (non-volatile memory) in...
User Guide - Page 20
... at the right is printed, the printer turns off. To set the settings to defaults. Load Default Setting? When the message shown at the right is printed in the function setting mode,
press the FEED button. The settings are set functions by pressing buttons. Setting Mode Finished.
(2) Changing software DIP switch settings
When the message shown at the right...
User Guide - Page 21
... shown at the right is selected (operation 1). Yes: Feed SW / No: Power SW" HINT
in the function setting
mode, the POWER lamp blinks once. Verify that the POWER lamp blinks.
DIP SW-1=******** Change Setting? The leftmost bit is the most significant bit (bit 8) and the rightmost bit is the least significant bit...
User Guide - Page 24
...Auto power off
bit4 Character set
bit3 Auto loading
bit2
Transmission mode
bit1
selection
1 Disabled
0 Enabled
1 JIS code
0 Shift JIS code
1 24-dot
0 ...
*1 If a setting not listed above is specified, thick paper (125 µm) is selected.
See Section 12, Options and Consumable Parts, for details of papers.
*2 For details, see DPU-3445-20 THERMAL PRINTER TECHNICAL REFERENCE.
-...
User Guide - Page 25
... out, while
holding the connector hook.
- 22 - An interface cable is connected, the printer uses serial transmission. See Section 11, Specifications, for details of interface specifications.
To remove the cable, pull it is selected according to the software DIP switch setting at power on and send data from the host computer to perform serial...
User Guide - Page 26
NOTE The host computer must conform to the printer. Q Infrared transmission by IrDA
(1) Turn the printer off. (2) Turn the printer on the model and environmental conditions.
Within 50 cm
HINT • ... connecting the
interface cable to it correctly. Verify that the printer prints it . (3) Place the infrared transmitter/receiver of
the host computer and the infrared transmitter /receiver of...
User Guide - Page 27
...ERROR lamp lights.
To use the printer for five seconds. When the lamp starts blinking, recharging begins. (6) The POWER lamp will turn the printer off . At this time, when the paper is not set... or discharged before recharging. HINT • The printer cannot print or receive data while it is installed in the printer connected with exclusive battery charger. Never touch the ...
User Guide - Page 30
...; Are the transmission conditions for repair. Replace it is lit or the POWER lamp blinks.
· See the Lamp Display on page 9. · Is the printer function setting correct ? Q The printer does not print.
· Is the interface cable connected correctly ? · Is the interface cable that meets the Interface Specifications listed on .
· Is the...
User Guide - Page 31
...; 89 × 29.5mm*2
(with Ferrite core
1.8 m (length) (recommended)
· Connector signals
Pin
Signal
1
RXD
2
TXD
3
BUSY
4
CHK
5
SG
6
FG
654321
on model type.
11 SPECIFICATIONS
Q Printer Specifications
Item
Specification
Printing method Characters per line
Thermal 52*1
Character size (H × W) Standard size: 24 dots × 12 dots (H × W) Kanji size: 24 dots...
Seiko DPU-3445-30A-E Reviews
We have not received any reviews for Seiko yet.