BlackArmor Backup User Guide
Page 120
...cases, there is red. The hard disk is usually a sticker on the drive that there is done using special connectors (called a host adapter) to connect them to the sockets. Aside from six to 14 SCSI hard disks installed in the PC. (There are three plugs on ...motherboard does not necessarily damage the electronics of the disk or the motherboard. Copyright (c) 2009 Seagate Technology LLC. the marked thread connected to pin #1 of the socket. B.1.2 Motherboard sockets, IDE cable, power cable There are two slots on the motherboard to which incorrect connection damaged the electronics of ...
...cases, there is red. The hard disk is usually a sticker on the drive that there is done using special connectors (called a host adapter) to connect them to the sockets. Aside from six to 14 SCSI hard disks installed in the PC. (There are three plugs on ...motherboard does not necessarily damage the electronics of the disk or the motherboard. Copyright (c) 2009 Seagate Technology LLC. the marked thread connected to pin #1 of the socket. B.1.2 Motherboard sockets, IDE cable, power cable There are two slots on the motherboard to which incorrect connection damaged the electronics of ...
BlackArmor Backup User Guide
Page 125
...The operating system should detect the SATA controller and install the appropriate software. you can use a Y-adapter that come with sevenpin keyed connectors. Most systems that splits a lead in the boot-up messages...download a copy of order, or the hard disk is not formatted. Copyright (c) 2009 Seagate Technology LLC. It is also possible that will let you enable SATA for the ports you are using ...or maybe you will need a Molex-to-SATA adapter. If you will just need to change any . Attach one SATA power connector. Then plug the power-supply lead or use both at least one end...
...The operating system should detect the SATA controller and install the appropriate software. you can use a Y-adapter that come with sevenpin keyed connectors. Most systems that splits a lead in the boot-up messages...download a copy of order, or the hard disk is not formatted. Copyright (c) 2009 Seagate Technology LLC. It is also possible that will let you enable SATA for the ports you are using ...or maybe you will need a Molex-to-SATA adapter. If you will just need to change any . Attach one SATA power connector. Then plug the power-supply lead or use both at least one end...
User Guide
Page 6
...BlackArmor NAS 110 server kit includes: • BlackArmor NAS 110 server • Power adapter • Ethernet cable • Installation CD, including software, product documentation, and warranty information • BlackArmor Quick Start Guide BlackArmor® NAS 110 User Guide 7 About This Guide 1. Note: Step-by-step instructions for using the software tools are included in this guide apply to BlackArmor NAS 110... the components and features of your Seagate BlackArmor® NAS 110 server (BlackArmor NAS 110 server). This guide contains complete setup instructions, as well as your...
...BlackArmor NAS 110 server kit includes: • BlackArmor NAS 110 server • Power adapter • Ethernet cable • Installation CD, including software, product documentation, and warranty information • BlackArmor Quick Start Guide BlackArmor® NAS 110 User Guide 7 About This Guide 1. Note: Step-by-step instructions for using the software tools are included in this guide apply to BlackArmor NAS 110... the components and features of your Seagate BlackArmor® NAS 110 server (BlackArmor NAS 110 server). This guide contains complete setup instructions, as well as your...
User Guide
Page 16
... Ensure that the server is not placed near a heat source. Step 2 Step 1 Figure 4: Connect power and network cables 2. Use the power adapter included in the kit to connect the BlackArmor NAS 110 server to the Ethernet port on the back of the server, as shown below. Setup Steps for Administrators ...8226; Ensure that you are not a BlackArmor administrator, skip to page 26. Ensure that the server's vents will not be covered or blocked and that the server won't be in the kit to connect the BlackArmor NAS 110 server to a switch or router on it. BlackArmor® NAS 110 User Guide 18
... Ensure that the server is not placed near a heat source. Step 2 Step 1 Figure 4: Connect power and network cables 2. Use the power adapter included in the kit to connect the BlackArmor NAS 110 server to the Ethernet port on the back of the server, as shown below. Setup Steps for Administrators ...8226; Ensure that you are not a BlackArmor administrator, skip to page 26. Ensure that the server's vents will not be covered or blocked and that the server won't be in the kit to connect the BlackArmor NAS 110 server to a switch or router on it. BlackArmor® NAS 110 User Guide 18