SanDisk SDCFX3-004G-bulk - 4GB Extreme III CompactFlash Card Bulk Package Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFX3-004G-bulk manuals!
Problems with SanDisk SDCFX3-004G-bulk?
Ask a Question
Free SanDisk SDCFX3-004G-bulk manuals!
Problems with SanDisk SDCFX3-004G-bulk?
Ask a Question
Popular SanDisk SDCFX3-004G-bulk Manual Pages
Product Manual - Page 10
... cards support the CF ERASE SECTOR and WRITE WITHOUT ERASE commands. If necessary, the cards will rewrite data from its use.
02/07, Rev. 12.0
1-4
© 2007 SanDisk Corporation The CompactFlash Memory Card soft error rate specification is an intrinsic part of the erase pooling functionality of SanDisk CompactFlash using hardware on-the-fly Error Detection Code/Error Correction Code...
Product Manual - Page 28
...
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 35
...Specification
Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup before -IOWR Address Hold following -IOWR -CE Setup before -IOWR -CE Hold following -IOWR -REG Setup... The minimum cycle time supported by Word 68 in Word 68. SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the ...
Product Manual - Page 47
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.3
Memory Mapped Addressing
When CompactFlash Memory Card registers are accessed via memory references, they appear in the common memory space window: 0-2K bytes as the X86 processors, must increment both the source and destination addresses when executing the memory to memory block move instruction. A byte ...
Product Manual - Page 49
... number of sectors of data requested to complete the request.
4.5.5
Sector Number (LBA 7-0) Register (Address-1F3[173]; SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- D4
IDNF
The requested sector ID is in this register is also accessed on a read...
Product Manual - Page 51
... Status Register clears a pending interrupt while reading the Auxiliary Status Register does not. No other bits in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376]; SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6[376]; D2
CORR...
Product Manual - Page 53
.... SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and...SanDisk Corporation
4-9
Rev. 12.0, 02/07 Implement a socket adapter that does not respond to accesses to the card or
b) if provided use an additional primary/secondary configuration in the Drive/Head Register. This may occur on the host data bus when this problem... floppy controller is installed and conversely to tri...
Product Manual - Page 56
...using the Write Without Erase command.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Table 5-1 Primary and Secondary I/O Decoding
Class 1 1 1 1 1 1 2 2 2 3 3 2 2 2
Command Set Multiple Mode Set Sleep Mode Stand By Stand By Immediate Translate Sectorb... Register
LBA Logical Block Address Mode Supported
Y
The register contains a valid parameter for this command.
Product Manual - Page 59
... M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in 512 byte increments Number of sectors per card (Word 7 = MSW, Word 8 = LSW) Reserved Serial number in ASCII (right justified) Buffer type (dual ported) Buffer size in Word Maximum No.
SanDisk CompactFlash Card OEM Product Manual
ATA Command...
Product Manual - Page 64
...
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer Cycle Time With Flow Control. Table 5-9 Word 82 Description
Bit
Setting
Indication
0
0
SMART feature set not supported
1
1
Security Mode feature set supported
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not supported...
Product Manual - Page 65
...PIO Transfer Modes Supported.
© 2007 SanDisk Corporation
5-11
Rev. 12.0, 02/07 Table 5-11 Word 85 Description
Bit
Setting
Indication
0
0
SMART feature set not enabled
1
1
Security Mode feature set enabled via the Security Set Password command
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not enabled...
Product Manual - Page 70
... sectors (not the number of the sector where the error occurred. When the Read Multiple command is set and the data transfer will take place as that contained the error.
02/07, Rev. 12.0
5-16
© 2007 SanDisk Corporation The error reporting is attempted before the Set Multiple Mode command has been executed or when Read...
Product Manual - Page 73
This command must be the next command issued to the host in the Error Register. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product. Table 5-24 Extended Error Codes
Extended Error Code 00h 01h 09h 20h 21h 2Fh
35h, 36h 11h 18h
05h, 30-34h...
Product Manual - Page 74
... Series but has no impact on the CF Memory Card 4 bytes of data apply on Read/Write Long commands Enable Power on Reset...part of the ATA Specification. The 9AH feature is unique to CompactFlash Memory cards and are supported. Features 01H and 81H are used by the host to establish or select certain features.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set...
Product Manual - Page 106
...specifications. Limited Warranty
SanDisk CompactFlash Card OEM Product Manual
All failing products returned to SanDisk under the provisions of this limited warranty shall be returned.
Please contact SanDisk's OEM Support... or neglect; SanDisk reserves the right to repair or replace, at 866-436-6073 with prior authorization from SanDisk Corporation. Concurrently, SanDisk also reserves the...
SanDisk SDCFX3-004G-bulk Reviews
We have not received any reviews for SanDisk yet.