Poulan SM4018 Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan SM4018 manuals!
Problems with Poulan SM4018?
Ask a Question
Free Poulan SM4018 manuals!
Problems with Poulan SM4018?
Ask a Question
Popular Poulan SM4018 Manual Pages
User Manual - Page 2
... guide bar tip with any condition that might be observed to use steeltoed safety footwear with your saw work is running. Because a chain saw is a high-speed woodcutting tool, special safety precautions must be near the chain saw when starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. PLAN AHEAD S Read this manual...
User Manual - Page 3
... oil caps, screws, and fasteners securely tightened. S Use only Poulan PRO accessories and replacement parts as the bar is driven straight back toward the operator. S Turn the engine off and let saw chain is intended for two-handed use metal to hold the flywheel when servicing the clutch, structural damage to the flywheel can cause material...
User Manual - Page 4
... handlebar so it .
S Do not overreach.
You must follow all safety precautions, instructions, and maintenance in this danger. Follow manufacturer's chain sharpening and maintenance instructions. S Use extreme caution when re-entering a previous cut above shoulder height. Keep the fingers of the guide bar. Never reverse right and left hand positions for your saw.
A Reduced...
User Manual - Page 5
...not recommended and may push the guide bar rapidly back toward the operator if kickback occurs. This
Computed kickback angle (CKA) Table
MODEL SM4018
BAR
P/N
Length
952044418
18″... guide bar and chain combinations meet the CKA requirements per standard.
CHAIN BRAKE AND CKA ANGLE S Chain Brake, designed to stop the chain in accordance with CSA and ANSI standards. Repairs on...
User Manual - Page 6
... not guarantee the avoidance of this manual, use of this adjustment before you are legally responsible for maintaining the operating condition of California, Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington require by hand counterclockwise until guide bar stops against clutch drum sprocket. If you operate a chain saw . Failure to follow all fasteners...
User Manual - Page 8
... and fast idle are set by pulling the front hand guard back toward the front handle as far as dry grass or fuel to provide quicker starting or after use. OPERATION
KNOW YOUR SAW
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW.
See CHAIN TENSION under the ASSEMBLY section. The CHAIN BRAKE is...
User Manual - Page 9
...idle to the full extent (to operate on the ground as this manual. Push the choke/fast idle lever in storage. ly when refueling. A 40:1 ratio is trying to the STOP position. Always read and follow the instructions... (95 ml) of oil with the choke/ fast idle lever at a ratio of rope per pull. Genuine Poulan or Poulan PRO bar and chain oil is free to the ON position.
2.
To start...
User Manual - Page 10
...chain should activate. CUTTING METHODS
IMPORTANT POINTS S Check chain tension before first use the weight of the guide bar fall forward and contact the stump. S Keep the chain out of kickback. Slowly press the primer bulb 6 times. 4.
S This saw and repair or replace parts...when the chain brake is pushed forward, either manually (by hand) or automatically (by an authorized service dealer....
User Manual - Page 13
... the saw After each use Air filter Every 5 hours* Chain brake Every 5 hours* Spark arresting screen and muffler Every 25 hours* Replace spark plug .
Before each use Bar lubrication Before each use Chain tension Before each use Chain sharpness . . . . . Before each use For loose parts Before each use Inspect and Clean: Bar Before each use...
User Manual - Page 14
.... CARBURETOR ADJUSTMENT
WARNING: The chain will not idle. The chain must be necessary if you notice any wires are re- The carburetor has been carefully set at idle speed. It is too slow. Rinse with a
wire brush. Air dry com- Reinstall cylinder cover and 3 screws. Notice the orientation of air filter.
installed correctly (see illustrations) to...
User Manual - Page 16
... requires repair.
1.
The policy of guide bar and chain, and normal adjustments explained in
the instruction manual such as follows from defects in our judgement affects its products. Fuel not reaching
carburetor.
1. Engine will run only a few seconds after starting.
1. Chain brake engaged. 4. Clean or replace plug and regap. 3. Disengage chain brake. 4. Parts and...
User Manual - Page 17
... IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Call: 1--800--554--6723 MAINTENANCE, REPLACEMENT AND REPAIR OF EMIS- OWNER'S WARRANTY RESPONSIBILITIES: As the small off --road engine is purchased. If you should contact your instruction manual. ment of any questions re- Poulan/WEED EATER is not liable to you are responsible for presenting your
nearest authorized service center or...
Parts List - Page 1
... 67. 530015826 68. 530038593 69. 530069611
Description
Washer--Clutch Assy. Heat Clip -- Clutch Kit --
PARTS LIST NO.
530164718
DATE
3/05/08
Replaces 530164718 -- 11/29/06
PPAARRTTSSLLIISSTT
Note: Illustration may differ from actual model due to design changes
CHAIN SAW MODEL(s)
SM4018
PAGE NO.
1
41 40
39
38
37 36 35 34
30
33
32
31...
Parts List - Page 2
... & 31)
17. 952030150 Spark Plug (RCJ --- 7Y)
33. 530069608 Kit--- Part No. Start Inst. PARTS LIST NO.
530164718
DATE
3/05/08
Replaces 530164718 -- 11/29/06
PPAARRTTSSLLIISSTT
Note: Illustration may differ from actual model due to design changes
11
12 13 14
1 2 3 4
56
CHAIN SAW MODEL(s)
SM4018
PAGE NO.
2
23
24
25
15
16 17
26 27...
Parts List - Page 3
CHAIN SAW MODEL(s)
SM4018
PAGE NO.
3
530015814 Screw
530053274 Assy--Isolator Spring
n = NEW PART NUMBER FOR THIS IPL
K= REFER TO THE SERVICE REFERENCE INDICATED FOR MORE INFORMATION. (LOCATED AT END OF IPL) If your unit does have been built with or without the spring and screw shown below . PARTS LIST NO.
530164718
DATE
3/05/08
Replaces 530164718 -- 11...
Poulan SM4018 Reviews
We have not received any reviews for Poulan yet.