Panasonic WV-CF102E Support and Manuals
Get Help and Manuals for this Panasonic item
This item is in your list!
View All Support Options Below
Free Panasonic WV-CF102E manuals!
Problems with Panasonic WV-CF102E?
Ask a Question
Free Panasonic WV-CF102E manuals!
Problems with Panasonic WV-CF102E?
Ask a Question
Popular Panasonic WV-CF102E Manual Pages
Service Manual - Page 1
...equivalent to -noise ratio: Minimum illumination: Switch function:
Lens: Focal length: F number: Angle of law. WV-CF102
SPECIFICATIONS
The Product with PbF
Power source and power consumption: Image sensor: Effective pixels: Scanning area: Scanning system: ... 90° Vertical: 65°
© 2 0 0 9 Panasonic Corporation
All rights reserved. AVS0901083C8
Colour CCTV Camera
Model No.
Service Manual - Page 2
..., it should be serviced or repaired only by the " Y " mark on the schematic diagram and the replacement parts list. About Lead Free...problems.
IMPORTANT SAFETY NOTICE
8 There are special components used in attempting to advise non-technical individuals of this equipment which are broken. Any attempt to service or repair the product or products dealt with manufacturer's specified parts...
Service Manual - Page 3
... THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. DISCLAIMER OF WARRANTY
IN NO EVENT SHALL Panasonic Corporation
BE LIABLE TO ANY PARTY OR ANY PER- STANDARD ACCESSORIES
Operating Instructions 1 pc.
Service Manual - Page 4
... DIAGRAM
SENSOR BOARD ...4-1 MAIN BOARD (1/2) ...4-2 MAIN BOARD (2/2) ...4-3 I/F BOARD ...4-4 POWER BOARD ...4-5 CONDUCTOR VIEW SENSOR BOARD ...5-1 MAIN BOARD...5-2 I/F BOARD ...5-3 POWER BOARD ...5-4 EXPLODED VIEW (1/4) (MAIN UNIT-1) ...6-1 (2/4) (MAIN UNIT-2) ...6-2 (3/4) (CAMERA UNIT)...6-3 (4/4) (PACKAGING) ...6-4 REPLACEMENT PARTS LIST ...7-1
Service Manual - Page 5
... VD2 that is prioritized over INT is installed. Default setting: OFF Important: In the case of "ON" setting, noise may be increased in the vicinity...camera selects black-and-white mode if the picture is dark, or color mode if the picture is established by utilising the SENSE UP function for B/W images. OFF: Does not compensate. e Dip switch Selects ON/OFF of the object. Default setting...
Service Manual - Page 6
...Panning table Adjusts the panning position of the camera.
t Azimuth adjuster Adjusts the azimuth angle of the camera. • Backlight compensation selector [BLC] ON: Compensates the background automatically if it is set to ON to adjust focus. Default setting: OFF Note: Under some conditions, such... to detect the backlight level. OFF: This mode is used when the front of the camera.
Service Manual - Page 7
...
To Extension Cable
Fig. 1-4
Cable of EVR Adjustment Kit
Fig. 1-1
8 EVR Interface Board as shown in Fig. 1-2. (Part Number: V0JA0039AN) CN2
CN1
To I/F Board CN5
To Cable of the Colour CCTV Camera WV-CF102. 8 Oscilloscope 8 Frequency Counter 8 Vectorscope 8 Underscanned Colour Video Monitor 8 12 V DC Power Supply Unit 8 Personal Computer (Windows XP with 25-pin Parallel
Port) 8 Lux...
Service Manual - Page 9
... from the Camera Unit. Remove two screws.
Camera Unit
Extension Cable...the Sensor Board and remove the Sensor Board from the Camera Unit as shown in Fig. 2-10. 8 Referring... Case and remove the CCD Bottom Case from the Camera Unit. Camera Unit
CN2
CN1
Fig. 2-10
8 Referring to Fig...the Main Board, remove the Main Board from the Camera Unit. Remove two screws.
Sensor Board
Main Board
...
Service Manual - Page 10
... Board
12 V DC Power Supply Unit
Vectorscope
Underscanned Colour Video Monitor
Video Output Connector
WV-CF102
75 Ω
Test Chart
Power Cable
12 V DC Power Supply Unit
Fig. 3-1
8 Connect the Underscanned Colour Video Monitor to the Video Output Connector of the Underscanned Colour Video monitor with this initial setting, uniess otherwise specified.
8 The adjustments should be...
Service Manual - Page 11
...
Test Point: Video Output Connector
Adjust:
Lens
8 Open the Lens iris.
8 Set the Radiation Chart 1.2 m away from the internet and arrange into C:¥Program Files¥ by file name "iotest")
7. Open the iotest folder. 2.
Installation of the Video Monitor. Execution of "iotest Setup" program screen.
6. Open DISK1 file. 4. Click OK button of "iotest...
Service Manual - Page 13
...click READ(R) button, you can confirm the setup data. 8 If you click READ+SAVE(S) button, you can save the data of the Camera. 8 If you can finish the EVR...Computer.
(Data are just example)
Note: If "SLAVE-ADDRESS Receiver Error" appears, click Option (O) and change "WAIT" valume within the ... key of the Personal Computer or click the white colour Button on the right side of the Adjustment menu and...
Service Manual - Page 15
... White Balance Adjustment
Test Point: Video Output Connector 8 Confirm that the item "9.1. 3200K White Balance
Adjustment" displayed. 8 Keep the Colour Temperature at 3 200 K. 8 Aim the Camera at the Logarithmic Gray Scale Chart. 8 Set the Mode Switch of the Vectorscope to NTSC mode. 8 Adjust data with ARROW Keys M< of the Personal Computer for next...
Service Manual - Page 16
...; 5 %.
(10.2.a) 3200K R-Y Gain Adjustment
Test Point: Video Output Connector 8 Confirm that the item "10.2.a. 3200K R-Y Gain
Adjustment" displayed. 8 Keep the Colour Temperature at 3 200 K. 8 Aim the Camera at the Colour Chip Chart. 8 Set the Gain Control of the Vectorscope to the normal
position. 8 Adjust data with ARROW keys M< of the Personal
Computer so that...
Service Manual - Page 18
... KIT THROUGH EVR INTERFACE BOARD
2
1
CN5
10
9
29
30
(SW5)
CN3
1
2
E2
5
1
CN2
1
5
(Connect by using the Extension Cable and
the Extension Board Ass'y for Servicing)
E11
50
2
49
1
CN2
(IC2)
50
1
49
2
CN1
TD71 (TD70) (14MHz)
(TD70 is placed in the back)
4
CN3
1
SENSOR BOARD
29
1
30
2
CN3
MAIN BOARD...
Panasonic WV-CF102E Reviews
Do you have an experience with the Panasonic WV-CF102E that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Panasonic yet.
Earn 750 points for your review!