Panasonic EY3552 - 18V METAL SAW Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic EY3552 manuals!
Problems with Panasonic EY3552?
Ask a Question
Free Panasonic EY3552 manuals!
Problems with Panasonic EY3552?
Ask a Question
Popular Panasonic EY3552 Manual Pages
EY3552 User Guide - Page 3
... the outlet. Distractions can cause you to use the metal cutter safely. •This manual and product use and all of electric shock.
- 3 - Keep cord away from heat, oil, sharp edges or moving parts. This Metal Cutter is a cutting tool, designed to be avoided.
SAFETY INSTRUC- SAVE THESE INSTRUCTIONS
Work Area Safety
1) Keep work area clean and...
EY3552 User Guide - Page 4
... with specifically designated battery packs. Battery tool use . Inserting battery pack into account the working conditions and the work to a rotating part of ...charger specified by the manufacturer. Do not wear loose clothing or jewellery. Power tool use common sense when operating a power tool. Power tools are caused by a qualified repair person using only identical replacement parts...
EY3552 User Guide - Page 5
... back toward the operator;
- Contact with a "live " and shock the operator.
• When ripping always use blades with the blade. Blades that the safety of the workpiece toward the operator.
Investigate and take corrective actions to a stable platform. Supports must read instruction manual. Unsharpened or improperly set blades produce narrow kerf causing excessive friction,
- 5 -
EY3552 User Guide - Page 6
... closing before placing saw to authorized service center for replacement.
22) Do not start the blade when in its path. blade binding and kickback.
6) Blade depth and bevel adjusting locking levers must be tight and secure before use. Do not operate the saw is released.
5) Do not use any other material.
14) Do not clamp Metal Cutter in a vise...
EY3552 User Guide - Page 7
... battery pack.
3) CAUTION-To reduce the risk of inju- It can lead to a qualified service personnel when service or repair is designed to work together. Never carry charger by cord or yank it will not be stepped on, tripped over, or otherwise subjected to filter out microscopic particles. WARNING:
Some dust created by power sanding, sawing...
EY3552 User Guide - Page 8
... must only be replaced by a repair shop authorized by the manufacturer, because special purpose tools are required.
25) TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER). 21) Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth...
EY3552 User Guide - Page 9
... not use . If the charging lamp does not light immediately after the charger is completed, an internal electronic switch will automatically be triggered to the level of safety.
2.
Charging is completed. III. SETTING UP
Charging Battery Pack EY9251
Charge the battery pack when the cutting speed becomes too slow for more than one .
The...
EY3552 User Guide - Page 10
... the blade installed in place at the rear of the material. •Do not touch the saw
horse or bench? Replace the blade immediately if there are any cracks in it has not been properly connected. Fig.2 2.To remove the battery pack:
Press the two tabs on the blade, do not use the metal cutter, you use the metal cutter if...
EY3552 User Guide - Page 11
... cutter. Wait until the blade reaches full speed before storing the metal cutter. 2.Press the switch lock lever down before continuing work.
6.It is convenient for rip cuts and repeated cuts of same width.
•Remove battery pack. •Insert rip fence and adjust cutting width. (See Fig.6) •Fasten screw securely to an authorized service...
EY3552 User Guide - Page 12
... injury or damage to the tool caused by thin strips of workpiece. •When cutting, do not try to hold the cutter firmly with your hand. Fig.9 Fig.7 Proper Support of Material
Fig.8 Improper Support of the cut without leveling and properly supporting the workpiece, the blade will tend to set the depth of Material
- 12 -
EY3552 User Guide - Page 13
... will result.
- 13 - Have it could result.
5.Never engage the spindle lock while blade is solidly supported (See Fig.10), never on your metal cutter has a brake, before setting the metal cutter down, make sure the blade has come to repair the metal cutter by an authorized service center. There are used. Keep clothing away from cut. •To resume cutting, start...
EY3552 User Guide - Page 14
... in the storage slot on genuine Panasonic replacement parts. MAINTENANCE
WARNING
To avoid severe personal injury, always remove the battery pack from being cut -out facing you. Be sure to retract (open) the
lower guard. 6.Carefully remove the blade. 7.Clean the metal cutter if necessary.
CAUTION: To assure product SAFETY and RELIABILITY, servicing should be hot right after...
EY3552 User Guide - Page 15
... which could make the metal cutter slippery or hard to handle. 4.Remove the blade and brush off any part of Battery pack
Ni-MH Battery pack (EY9251) •Charge the Ni-MH battery fully before storage in the storage slot on the metal cutter's body when not using it safe to use your metal cutter clean for replacement. It could result in...
EY3552 User Guide - Page 16
...unhardened ferrous material Thickness of material 0.3 mm - 6.0 mm (1/64" - 15/64") Blade for that recommended for cutting thin metal material (Optional accessory) •EY9PM17B For cutting unhardened thin ferrous material Thickness of material ...accessories not specified in this manual may result in a rough cut of same width Battery Pack •EY9251 Battery Charger •EY0110
- 16 -
EY3552 User Guide - Page 17
The instruction label on the charger or the latest general catalog. VII.SPECIFICATIONS
Metal Cutter (EY3552)
Motor voltage
18 V DC
Blade Speed
2900 /min (rpm)
Blade Size Outside diameter Arbor size
165 mm (6-1/2") 20 mm (25/32")
Maximum cutting depth Dimensions (L × W × H)
3 - 56 mm (1/8" - 2-13/64") (φ165 mm blade)
345 × 198 × 264 mm (13-37/64...
Panasonic EY3552 Reviews
We have not received any reviews for Panasonic yet.