Oreck XL2800H2 Support and Manuals
Get Help and Manuals for this Oreck item
View All Support Options Below
Free Oreck XL2800H2 manuals!
Problems with Oreck XL2800H2?
Ask a Question
Free Oreck XL2800H2 manuals!
Problems with Oreck XL2800H2?
Ask a Question
Most Recent Oreck XL2800H2 Questions
How To Reconnect Wires To Lights
Had mtr repaired and wires to lots cut And not reconnected. Need wiring diag to show how to reconnec...
Had mtr repaired and wires to lots cut And not reconnected. Need wiring diag to show how to reconnec...
(Posted by Rweeden361 10 years ago)
What Is The Part Number For The Belt For Oreck Xl2800h2
(Posted by elivitsanos 10 years ago)
Popular Oreck XL2800H2 Manual Pages
Owners Guide - Page 1
Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis • Accessories S I M P LY
A M A Z I N G™
USER'S GUIDE
XL2800H2
HIGH SPEED UPRIGHT VACUUM CLEANER WITH
™
CLEANING SYSTEM
•IMPORTANT•
SAVE THIS BOOKLET!
Owners Guide - Page 2
... Belt, To Adjust or Replace Brush page 6 Bulb Replacement, Stuffing or Blockage, Using a Fresh Air Tab page 7 Troubleshooting Guide page 8
2
IMPORTANT
SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should still fail to fit, contact an electrician to pick up toxic material such as a handle, close door on cord. Keep the unit moving parts. • Do not...
Owners Guide - Page 3
... Service
Your ORECK vacuum cleaner is valid only if you retain proof of purchase from ORECK or an ORECK Authorized Retail Dealer for this product. Any commercial use .
ORECK does not authorize any person or representative to assume or grant any part subjected to state.
3
Fresh Air Tabs
PART NUMBER
CCPK8DW
0300604 00965-0019 AIRTABS
Warranty
ORECK MANUFACTURING COMPANY: (ORECK...
Owners Guide - Page 4
... holes and tighten firmly until it snaps.
4 Plug (Cord Assembly)
Machine should be in upright position when inserting cord assembly into handle.
Dust seal will close automatically
BAG INSTALLATION : 1.
BAG REMOVAL : 1. Unsnap bag door from
cardboard collar upwards.
3. Slide upper handle section (1) over matching section of your vacuum,
11
the parts have been numbered 9
as follows...
Owners Guide - Page 5
... outer bag, vacuum it or shake it out. When buying replacement belts, use .
If there is dust in the base plate of the paper bag is to trap dirt, but at maximum efficiency, change the dust bag frequently. Celoc® Hypo-Allergenic Filter System The CELOC SMMS outer bag of your cleaner. Operating Recommendations This new ORECK XL High-Speed Upright...
Owners Guide - Page 6
... bearings, make sure both bearings must be adjusted. When rotating, both bearing assembly settings are the same and face up when replacing the brush roll. If a previous adjustment has already been made and bristle height does not extend above base plate at ends of the brush pulley and roll the belt around the pulley.
Owners Guide - Page 7
... reach the blockage, remove base plate. C
4. Replace and tighten
collar until collar locking tabs
are locked in the carpet. See illustration F. Using A Fresh Air™ Tab
Your ORECK XL vacuum cleaner has a special FRESH AIR tab pocket. If your vacuum cleaner does not pick up properly, or makes unusual noise and the outer bag does not fluff up...
Owners Guide - Page 8
... filter dust bag full? • Are pores of Oreck Holdings, LLC.
75268-05 REV D
8
12/02 ECN# R-6815
Replace brush if bristles do not extend beyond base plate.
Revolving brush is firmly plugged into wall outlet. Make sure words "old" or "new" match at both ends.
Troubleshooting Guide
WARNING: Unplug cord from data plate.
©2002 Oreck Holdings, LLC.
PROBLEM
POSSIBLE...
Oreck XL2800H2 Reviews
We have not received any reviews for Oreck yet.