Oki OKIPOS 441 SerialBlack Support and Manuals
Get Help and Manuals for this Oki Data item
This item is in your list!
View All Support Options Below
Free Oki OKIPOS 441 SerialBlack manuals!
Problems with Oki OKIPOS 441 SerialBlack?
Ask a Question
Free Oki OKIPOS 441 SerialBlack manuals!
Problems with Oki OKIPOS 441 SerialBlack?
Ask a Question
Popular Oki OKIPOS 441 SerialBlack Manual Pages
Users Guide - Page 2
...set out in U.S.A. The above statement applies only to printers marketed in Canada. The above statement applies only to printers marketed in EU. Reproduction of any part of this manual in any errors...Part 15 of Communications. Trademark acknowledgments OKIPOS441: Oki ...instruction manual, may cause harmful interference to radio communications. These limits are subject to change without OKI...
Users Guide - Page 3
......15 5-2. Installing the Roll Paper Guide 18
6. Control Panel...21 6-2. Errors...22 6-4. Power Supply Specifications...37
10. USB Interface Model...41 10...Setting...38 10-1. RS-232C Interface Model...40 10-2. Ethernet Interface Model...41 10-5. Unpacking and Installation...2 2-1. Unpacking...2 2-2. Maintenance...4
3. Setup...6 4-1. Connecting to a Peripheral Unit 11 4-5. Installing...
Users Guide - Page 28
... Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the buzzer sounds five times. (Refer to the separate Specifications Manual for details.) (Holding down for 2 more seconds)
(6) The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after the buzzer sounds six times. (Refer to the separate...
Users Guide - Page 38
...Refer to the separate Specifications Manual for details.
5. Minimum resistance for diodes D1 and D2 (Ta = 25°C) are :
Collector current IC = 2.0 A
- 34 - External buzzer model: RMB-24
Voltage rating...units 1 and 2 cannot be known from the status command. ously, set the duty cycle ratio to the separate Specifications Manual for transistors TR1 and TR2 (Ta = 25°C) are :
...
Users Guide - Page 42
... recommended to use a pointed item like a pen or flat-blade driver screw to on again. Replace the DIP switch cover. Then secure it with the screw. The new settings take off the DIP switch cover, as given in the illustration below . Be sure to set the power switch to off . 2. The following is provided...
Users Guide - Page 43
... Auto Cutter *1 Always ON Command emulation USB mode *2 2 colors printing Reserved Print head model *3
ON
OFF
Should be set on
Invalid
Valid
Should be set on ) Models with a tear bar). A mechanical error will occur.
*2 USB interface model only *3 Do not change the default setting (Switch 1-8 = off )
Note: Do not enable the auto cutter for enabling/disabling the...
Users Guide - Page 44
Change the setting of DIP switch are all on, except for DIP switch No. 2 according to the following procedures. 1. Replace the serial interface board unit.
Switch 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8
...to change the communication settings.
Change the settings for switches 7 and 8. Then secure it . RS-232C Interface Model
The RS-232C interface model is equipped with the screws. 6.
Users Guide - Page 45
... DIP switch only.
10-4. Push the switch for one to their default, or ex-factory, settings. Red : Lights when packets are received. This will return the settings of the red and green LEDs. Ethernet Interface Model
n Initializing Settings Set the push switch as 100BASE-TX. After that, push the switch once again in that state...
Users Guide - Page 46
... Green : Lights when pockets are all off. Wireless LAN Interface Model
DIP-SW 2
Switch 2-1 2-2
ON Fixed at OFF
Initialize of DIP switch are received. Change DIP Switch 2-2 to ON to initialize the setting information when the power is turned on. The factory settings of setting information
OFF - LED DIP switch 2
ON
OFF No. 1 2
DIP...
Users Guide - Page 53
For instructions on setting the memory switch, please refer to the separate Specification Manual.
This connector mates with the return
sides connected to ...using the nInit signal (#31 pin). During factory output, IFEE 1284 printer device ID reply will be set to the separate Specification Manual. 4. To get the device ID, change memory switch 6-C to low active signals. Reset can be...
Users Guide - Page 55
... below shows the factory settings for the memory switches. Memory Switch Settings
Each memory switch is stored in EEPROM. For details on the functions and settings of memory switches, see the separate Specification Manual. Memory Switch 0 1 2 3 4 5 6 7 8 9
Hexadecimal Code 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
WARNING
Changing the memory switch settings can cause the...
Software Manual - Page 4
... Connection 11 Uninstalling the Driver Software from Windows 2000 and XP . . . . . 16
Installing the Driver Software on Windows Vista 18 For USB Connection 18 For Parallel Port (LPT1) Connection 20
Software Features 26 OKIPOS 441 Setup Utility 26 Port Emulator 26
Windows 2000/XP/Vista Printer Driver Settings 27 Setting the Printer 27 Setting the Paper Type 28...
Software Manual - Page 10
... paper and how to connect the printer to your computer. USB Connection
1. To view the manual, click Document at the bottom right of the Windows desktop to the specific type of the printer hardware and automatically installs the driver software. The Windows plug-and-play feature detects the connection of printer connected.) If the...
Software Manual - Page 26
... Windows versions prior to select the utility only without also installin the driver software. Important! Note that support only serial printers to access your printer through a USB or Ethernet connection.
Port Emulator
This feature sets up an Ethernet interface card. This utility is not supported on Windows versions prior to Windows 2000 SP3.
Important!
Software Manual - Page 49
...
3,000 mm
A4
210 mm
297 mm
Letter
x
8.5 inches 11 inches
a. "Receipt" length denotes variable length.
If you are supported. If you should be set the width no greater than the actual paper size to Receipt
49 • Windows 2000/XP/Vista Printer Driver Settings
The width value denotes the printable range, and should...
Oki OKIPOS 441 SerialBlack Reviews
Do you have an experience with the Oki OKIPOS 441 SerialBlack that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Oki yet.
Earn 750 points for your review!