Nady 8W-1KU Support and Manuals
Popular Nady 8W-1KU Manual Pages
Manual - Page 2
... this Manual...2 System Features...3 Quick User Controls Guide...4 System Operation...8
8W-1KU Receiver...8 HT-1KU Handheld Microphone Transmitter 12 BT-1KU Bodypack Transmitter 14 Specifications...17 Cautions and Troubleshooting 19 Miscellaneous Tips...20 Frequency...22 Accessories...22 Service Information...22 Warranty...23
Introduction
Thank you for choosing the Nady 8W-1KU wireless system...
Manual - Page 3
...-of sight
• Eight complete, independent wireless receivers with 1000 user-selectable UHF frequencies
• Works with any combination of available instrument, handheld and/or lavalier UHF transmitters
• True Diversity circuitry with two complete front ends per band
8W-1KU Octo Receiver
• Unsurpassed state-of-the-art PLL UHF performance with 120dB dynamic range and operation...
Manual - Page 4
...HT-1KU/BT-1KU transmitters' IR Window (34/43) by one step at a time DOWN BUTTON To change the receiver...receiver A or B is active when transmitter is loudest output)
12. Press the ASC Button (5) once and wait one of GRP (00-09)/CH (00-99), RF signal strength indicator 1-6 bars, and Volume Levels (0-63)
9. If the download is for the RX to respond. Quick User Controls Guide
8W-1KU Receiver...
Manual - Page 5
Quick User Controls Guide
8W-1KU Receiver: Rear View
13. RACK EARS Left and Right rack ears are built into the unit
13a....
5 ANTENNAS ½ wave antennas connect to DC Input Jack (18)
21. MUTE (SQUELCH) CONTROLS Control the mute level for each receiver-fixed Mic level
16. DC INPUT JACK For using external DC adapter to rack ear holes for maximum range; RF CONNECTORS Antenna jack B...
Manual - Page 8
... (Up) or (Down) Buttons (7) are off the receivers.
Rack-mounting the Receiver
The Nady 8W-1KU receiver wireless system has built-In Rack Ears (13). When the Set Button (6) is pressed for two seconds to work properly. The Diversity A/B (2) and the AF PEAK LED (3) are on both sides and install the receiver onto the rack.
This could degrade the performance...
Manual - Page 9
... that channel for use. This avoids duplicate selection
Selecting the 8W-1KU Receiver Volume Level / Group / Channel
This section will also aid in about five seconds. Press the Set button to be desirable open channels. Repeat these procedures for the remaining receivers to enter the Group setup mode and the Group icon will flash, then press...
Manual - Page 10
...receivers' volume settings as selected by the Sum Volume Level display, the system output is needed. Note that a counterclockwise (maximum mute) setting will also yield a quieter mute function, which the RF Level Meter (12) and one of HT-1KU and BT-1KU...and Peak LED Indicator
The 8W-1KU receiver has an AF Peak LED (3) display for each receiver and each 8W-1KU receiver's Mute Control (16) ...
Manual - Page 11
... is an eight receiver unit, eight transmitters on the same frequency and mix the output of these transmitters into one wireless receiver. Note: Only one transmitter can be used with one with each receiver.
11 Your 8W-1KU receiver is not possible to use . It is now operational and ready to the following instructions for the HT-1KU Handheld or...
Manual - Page 12
... the transmitter body. To install the batteries onto the battery compartment, unscrew the Battery Compartment Cover (22) by the flashing "BATT" Battery Meter Icon (33).
Programming the HT-1KU to the Selected Channel
The transmitter can provide up to 8-10 hours of use or anytime later. The factory default setting for Volume -10dB is...
Manual - Page 13
.... During manual programming, press the Set button to confirm the selection or the selected function will flash for the first receiver. The ...HT-1KU, which is completed. Then start , press the Set button once. Note, if procedure is transferring during the three seconds of the same channel as desired. To start AUTO-SCAN on the receiver. After programming is finished, press the Set...
Manual - Page 15
.... The backlight on the receiver to be off , slide the Off/Mute/On switch to "MUTE" and then "OFF". When a group selection is set using the IR Sync function or manually on the transmitter itself. The level is same for the channel selection.
IR Sync Programming: Use the wireless IR LED Receptor Sensor (43...
Manual - Page 17
Specifications
SYSTEM OVERALL SPECIFICATIONS Operating Frequency Range
Freq. Synthesized PLL System Frequency Stability Frequency Response Dynamic Range Harmonic Distortion Modulation Operating Range
(U.S.) Band 1: 672.000-696.975MHz, (Int.) Band 2: 795.000819.975MHz (1000 channels switchable) 25kHz/ step
Manual - Page 19
... frequency), often it can be set properly. with previously tuned systems all setups. in Selecting the 8W-1KU Volume Level / Group / Channel. One bar or less is set to the Selected Channel
To reprogram, you must be overcome by adjusting the receiver's Squelch Control (16) (see Adjusting the Squelch). Cautions and Troubleshooting
Feedback
Avoid acoustic feedback (howling...
Manual - Page 22
... Includes:
User' Manual (This manual) Two antennas Lav Mic for LT AC/DC power adaptor
Main Receiver Unit 8 combination (HT/ LT/GT) transmitters GT cable for GT
Accessories
Part Number
IC-U1K
FAMK -2
Description
Instrument cable for BT-1KU/GT transmitter, 3.5mm locking mini plug to the Support page at (510) 652-2411 for 8W-1KU receiver
Service Information
In the...
Nady 8W-1KU Reviews
Do you have an experience with the Nady 8W-1KU that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Nady yet.
Earn 750 points for your review!