Maytag MMV1175JZ Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MMV1175JZ manuals!
Problems with Maytag MMV1175JZ?
Ask a Question
Free Maytag MMV1175JZ manuals!
Problems with Maytag MMV1175JZ?
Ask a Question
Popular Maytag MMV1175JZ Manual Pages
Installation Instructions - Page 1
... 11 VENTING DESIGN SPECIFICATIONS 12 ASSISTANCE 14 Replacement Parts 14 Accessories 14
MICROWAVE HOOD COMBINATION SAFETY
W11485889B The appearance of Contents
MICROWAVE HOOD COMBINATION SAFETY 1 INSTALLATION REQUIREMENTS 2
Tools and Parts 2 Remove Cardboard Template 2 Location Requirements 2 Product Dimensions 3 Electrical Requirements 3 INSTALLATION INSTRUCTIONS 4 Remove Mounting...
Installation Instructions - Page 2
...Gather the required tools and parts before starting installation.
If installing the microwave near a left sidewall, make sure there is perforated.
NOTE: Depending on model, charcoal filters may be sure to it during the "Mark Rear Wall" and "Prepare Upper Cabinet" part of microwave oven)
C. See the "Venting Design Specifications" section.
2 A
B
C
D
E
FG
H
A. 3/16-24 x 3" round...
Installation Instructions - Page 3
...part # W11185746) is properly installed and grounded.
If the power supply cord is equipped with a cord having a grounding wire with a fuse or circuit breaker
Recommended:
■ A time-delay fuse or time-delay circuit breaker
■ A separate circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
For all governing codes... bump out mounting kit replacing the I bar mounting plate...
Installation Instructions - Page 4
...damage to the back of
B
microwave oven, set for recirculation installation.
NOTE: Skip this section if you are using recirculation installation. A A.
Damper plate
A....microwave oven is attached to the microwave oven, do not grip or use the door or door handle while the microwave oven is being handled. A
B
A. INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model...
Installation Instructions - Page 5
... in the blower motor screw holes, so that the motor cannot move.
A
A. Screws B. A
A. A B
A. Diagonal wire cutting pliers B. A B
A
B
A.
Reconnect the blower motor wire into the microwave oven. Blower motor wire B. A. Connector
A.
Damper plate 5 Blower motor bridge B.
Hold the blower motor wire, put the wire through the blower motor bridge. Check...
Installation Instructions - Page 6
... (as shown), performance will be poor.
6 Exhaust port IMPORTANT: If blower motor is not positioned with flat side facing the back of microwave oven.
Screws
Roof Venting Installation Only 1. Damper plate B. Lower blower motor back into the connector. 9.
Damper plate B. 13.
Reattach the two blower screws into the recessed holes in Step...
Installation Instructions - Page 7
... E. Top of cabinet. Mark the center of the upper cabinet. Cabinet opening , do not install the microwave oven.
1. Centerline
D A
C
B
2. End holes (on a minimum of one wall ...is butted up against the bottom edge of each stud, and draw a plumb line down each stud center. Support tabs F. Using measuring tape, find and clearly mark the vertical centerline of the cabinet.
■ If the ...
Installation Instructions - Page 8
...head bolts and toggle nuts or 1/4 x 2" lag screws. Set the mounting plate aside. This is level.
6. Using a keyhole...end holes are ideal hole locations.
7.
With the support tabs facing forward (see illustrations in the "Locate ...44.02 cm) from the bottom of the centerline, and mark.
10.
Wall Venting Installation Only
Upper cabinet bottom
3/8" (1 cm)
4" (10.2 cm)
Centerline
6" (15...
Installation Instructions - Page 9
...and finger
tighten the bolt to the thickest part of the microwave oven.
Securely tighten all contents from the...bolts. NOTE:
■ If the wall behind the microwave oven (as installed) has a partial wall covering (for example, the...16-24 x 3" round-head bolt B. If installing on the wall. 4.
Prepare Upper Cabinet
1. With the support tabs of the upper cabinet, make sure toggle nut...
Installation Instructions - Page 10
... cabinet near the 3/8" (10 mm) holes.
10
A
B A. A
B C
D
3. Damper assembly C. If adjustment is no gap between upper cabinet and microwave oven. A
A. Support tabs
5. NOTES: ■ Some upper cabinets may not have packing spaces, install your model, it does not have packing spacers. Longer or shorter bolts are available at the top, and the damper blade...
Installation Instructions - Page 11
... nut, screw the bolts into a grounded 3 prong outlet. ■ See the User Instructions for troubleshooting information. Then tighten with #6 x 3/8" sheet metal screw. Upper cabinet cutout E. Do not use an extension cord. Plug microwave oven into a grounded 3 prong outlet. Save Installation Instructions for filter placement. Bolts
NOTE: Avoid damage to damper assembly. Then...
Installation Instructions - Page 12
...⁄4" x 10" to 6" = 5 ft (8.3 x 25.4 cm to vent air outside, unless using recirculation installation. Rectangular-to-Round Transition NOTE: The minimum 3" (7.6 cm) clearance must exist between the top of the microwave oven and the transition piece. VENTING DESIGN SPECIFICATIONS
This section is proper clearance within walls or ceilings, attics, crawl spaces or garages...
Installation Instructions - Page 13
... performance, use no more than three 90° elbows.
Recommended Vent Length
A 31⁄4" x 10" (8.3 x 25.4 cm) rectangular or 6" (15.2 cm) round vent should be installed to keep the damper from sticking.
13 Two 90° elbows = 20 ft (6.1 m) B. 1 wall cap = 40 ft (12.2 m) C. 1 rectangular-to-round transition piece = 5 ft (1.5 m) D. 2 ft...
Installation Instructions - Page 14
...Following is a list of the installation hardware needs to use when installing this microwave oven in the User Guide. ASSISTANCE
Call your authorized dealer or service center for details.
14 Accessories
Filler Panel Kits are available from your model and serial numbers located on the front frame of the microwave oven opening . Replacement Parts
If any of available replacement parts.
Maytag MMV1175JZ Reviews
We have not received any reviews for Maytag yet.