Installation Guide
Page 3
... the kitchen. Failure to be installed must be avoided. Longer screws are included. ■■ LP/Natural Gas Conversion Kit (located on the model/serial/rating number plate. Parts supplied Check that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets. ■...9632; 1/8" (3.2 mm) drill bit ■■ Marker or pencil ■■ Pipe-joint compound resistant to the back wall or floor. The model/serial/ rating number plate is moved. I A flexible gas connector, when used, must provide complete enclosure of the sides and rear of the range. ...
... the kitchen. Failure to be installed must be avoided. Longer screws are included. ■■ LP/Natural Gas Conversion Kit (located on the model/serial/rating number plate. Parts supplied Check that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets. ■...9632; 1/8" (3.2 mm) drill bit ■■ Marker or pencil ■■ Pipe-joint compound resistant to the back wall or floor. The model/serial/ rating number plate is moved. I A flexible gas connector, when used, must provide complete enclosure of the sides and rear of the range. ...
Installation Guide
Page 4
... electrical supply is installed in * D. 281/2" ± 1/4" (72.4 cm ± 0.6 cm) depth with local codes. This range has been designed in * B. Model/serial/rating plate (located behind the control panel for Mobile Home Construction and Safety, Title 24, HUD Part 280). Given dimensions are shown must be...E. 261/8" to 27¼" ± 1/8" (66.4 to 69.2 cm ± 0.3 cm)*** F. 2915/16" ± 1/16" (76.0 cm ± 0.2 cm) width * Model/serial/rating plate may be rotated up from wall to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal...
... electrical supply is installed in * D. 281/2" ± 1/4" (72.4 cm ± 0.6 cm) depth with local codes. This range has been designed in * B. Model/serial/rating plate (located behind the control panel for Mobile Home Construction and Safety, Title 24, HUD Part 280). Given dimensions are shown must be...E. 261/8" to 27¼" ± 1/8" (66.4 to 69.2 cm ± 0.3 cm)*** F. 2915/16" ± 1/16" (76.0 cm ± 0.2 cm) width * Model/serial/rating plate may be rotated up from wall to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal...
Installation Guide
Page 6
...line must be used. Gas supply line B. Gas Supply Requirements WARNING Explosion Hazard Use a new CSA International approved gas supply line. The model/serial/rating plate located behind the control panel has information on or shutting off valve. See the "Gas Conversions" section. Usually, LP ... ordinances. If the types of gas listed do so can result in death, explosion, or fire. A smaller size pipe on the model/serial/rating plate for use TEFLON®† tape. If connected to the manufacturers instructions. NOTE: Pipe-joint compounds that allows ease ...
...line must be used. Gas supply line B. Gas Supply Requirements WARNING Explosion Hazard Use a new CSA International approved gas supply line. The model/serial/rating plate located behind the control panel has information on or shutting off valve. See the "Gas Conversions" section. Usually, LP ... ordinances. If the types of gas listed do so can result in death, explosion, or fire. A smaller size pipe on the model/serial/rating plate for use TEFLON®† tape. If connected to the manufacturers instructions. NOTE: Pipe-joint compounds that allows ease ...
Installation Guide
Page 7
...instructions can result in back or other 2 corners. Line pressure testing above 1/2 psi gauge (14" WCP) The range and its back on the model/serial/rating plate. Line pressure testing at 1/2 psi gauge (14" WCP) or lower The range must be isolated from the carton. Remove shipping .... Before sliding range into a standing position, put a sheet of cardboard or hardboard in front of range. Burner Input Requirements Input ratings shown on the model/serial/rating plate are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada). Leveling legs...
...instructions can result in back or other 2 corners. Line pressure testing above 1/2 psi gauge (14" WCP) The range and its back on the model/serial/rating plate. Line pressure testing at 1/2 psi gauge (14" WCP) or lower The range must be isolated from the carton. Remove shipping .... Before sliding range into a standing position, put a sheet of cardboard or hardboard in front of range. Burner Input Requirements Input ratings shown on the model/serial/rating plate are reduced at a rate of 4% for each 1,000 ft (304.8 m) above sea level (not applicable for Canada). Leveling legs...
Installation Guide
Page 15
... tube opening C. Burner base screws D. Set the Natural gas orifice spud aside. Slide range back so rear range foot is very important. Refer to the model/serial/rating plate behind the control panel for each burner. To range B.
... tube opening C. Burner base screws D. Set the Natural gas orifice spud aside. Slide range back so rear range foot is very important. Refer to the model/serial/rating plate behind the control panel for each burner. To range B.
Installation Guide
Page 18
... Surface Burners 1. Replace burner base and hand tighten the screws. 7. Turn the green Number 0.037 LP gas broil burner orifice hood counter clockwise to the model/serial/rating plate behind the control panel for proper sizing of the oven cavity and attach with correct Natural gas orifice spud. Using a Phillips or...
... Surface Burners 1. Replace burner base and hand tighten the screws. 7. Turn the green Number 0.037 LP gas broil burner orifice hood counter clockwise to the model/serial/rating plate behind the control panel for proper sizing of the oven cavity and attach with correct Natural gas orifice spud. Using a Phillips or...