Maytag MGDB835DC Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGDB835DC manuals!
Problems with Maytag MGDB835DC?
Ask a Question
Free Maytag MGDB835DC manuals!
Problems with Maytag MGDB835DC?
Ask a Question
Popular Maytag MGDB835DC Manual Pages
Installation Guide - Page 5
... Steam models only: Cold water faucets located within 2 ft. (610 mm) of either side of 6" (152 mm) clearance behind dryer for your "Use and Care Guide." Also...Parts needed for electric dryers.
■■ If using the "Y" connector and short hose which are required. Check existing electrical supply and venting. Some codes limit, or do not permit, installation of installation and servicing...
Installation Guide - Page 8
.... It is properly installed and grounded in the "Assistance or Service" section of electric shock.
or 20-
Do not modify the plug provided with all local codes and ordinances.
Burner information...;■ If local codes permit, use with the type of gas available, contact your "Use and Care Guide." A time-delay fuse or circuit breaker is located on the model/serial rating plate for...
Installation Guide - Page 9
...
manual shutoff valve be installed within six (6) ft. (1.8 m) of the dryer.
2. Prepare dryer for each 1,000 ft. (305 m) increase in accordance with the B149.1, Natural Gas and Propane
Installation Code....plugged tapping D. 1/2" NPT gas supply line E.
IMPORTANT: If laying dryer on the model/serial number plate is recommended that complies with to avoid damaging the back of the dryer...
Installation Guide - Page 21
.... Be sure vent is level. For direct wire installation, turn on . Steam models only:
q Be sure the water faucets are set in a hard water area, use of a water softener is
recommended to the need for certain part replacement or repair. q Check for leaks.
NOTE: You may clog different parts of the water system, which will go back...
Use & Care Guide - Page 7
...Prevent†
Static Reduce
Cycle Details:
This is the default dryness setting. To reduce cycle time, at High Heat, quickly goes to...use the Sensing cycles. For best results, this cycle.
CYCLE GUIDE -
Small load: Fill the dryer drum with this cycle. ...cycles but is a long cycle with service voltage less than 1/4 full. On Steam Models for these cycles, Wrinkle Prevent without ...
Use & Care Guide - Page 10
... appears in 5-minute increments. See the "Cycle Guide" for more information about each cycle. NOTE: Not all options and settings are on fabric type, load size, and dryness setting. Not all cycles are available with all cycles.
The default temperature may adjust different settings, depending on all models. R emove garments promptly after cycle has completed...
Use & Care Guide - Page 11
... to adapt to different installations, environmental conditions, or personal...Cycles are displayed using the Air Only setting. 6. The drying rack is off) to adjust the default settings. 1. To use . Rest the rear support on the dryer back ledge.
3. ... and will need your model and serial number and the purchase date. Touch DRY LEVEL to save the new dryness level setting. Use the Drying Rack...
Use & Care Guide - Page 13
... if bulges, kinks, cuts, wear, or leaks are secure in the
Installation Instructions. Replace all parts and panels before servicing. Moving Care For power supply cord-connected dryers: 1. Gas models only: Cap the open fuel supply line. 5.
NON-USE, STORAGE, AND MOVING CARE
Steam models only: Install and store your dryer where it . To Use the Dryer Again...
Use & Care Guide - Page 14
...Installation Instructions.
Clothes not contacting the moisture sensors during the Steam function. See "Cycle Guide...The Air Only temperature setting has been selected.
...outside of lint or replace exhaust vent with ...to possibly avoid a service call. Using a vacuum...contact with the floor.
TROUBLESHOOTING
First try the solutions suggested...minutes. If the problem continues, call an...
Use & Care Guide - Page 15
...avoid a service call. See the Installation Instructions.
See the Installation Instructions. All four...setting on the load size.
The dryer was not removed from the steam valve. Check that water inlet hose is connected to garment care label instructions. Wrinkle Prevent does not enable Steam Refer to Cycle Guide... on some models), adjust the... synthetics. TROUBLESHOOTING
First try...
Use & Care Guide - Page 16
... cycle with a lower heat setting to resume cycle. Call for details. TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help - Allow the dryer to "Plan Vent System" in need of lint and debris.
• C onfirm that requires service. The dryer is in the Installaton Instructions for service.
16
Use & Care Guide - Page 17
... warranty gives you specific legal rights, and you also may not apply to correct improper product maintenance or installation, installation not in this major appliance is effective from defects in these parts that prevent function
of purchase including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Consumable parts (i.e. The cost of repair or replacement under this...
Quick Reference Guide - Page 1
... TURN ON THE DRYER
Appearance may vary across loads and cycles.
* NOTE: See "Cycle Guide" in U.S.A. Read your Use and Care Guide before using your energy savings.
All rights reserved.
Not all cycles, settings, and options are available with all models. SP
®/™ ©2014 Maytag. W10720372A W10720373A - Turn off for NORMAL. This...
Dimension Guide - Page 1
...Leveling legs 1/2" (13 mm) (3.6 washer capacity) or 1½" (38 mm) (3.8 washer capacity) depending model. See "Venting Requirements." Louvered doors with equivalent ventilitation openings are acceptable. ■■ Companion appliance spacing should be considered for ease of
installation and servicing. ■■ Additional clearances might be required for wall, door, and
floor moldings...
Dimension Guide - Page 2
INSTALLATION...details, see Installation Instructions packed with...tubing should be installed within 6 ft (1.8 m) of L.P.
Electric models only
To supply.... WATER (STEAM MODELS ONLY) REQUIREMENTS
The...Code ANSI Z223.1. An individual manual...installations have a 90° turn to the gas supplier and local codes, 3/8" approved tubing may be used . Gas models...9632; Plan installation to determine type...
Maytag MGDB835DC Reviews
We have not received any reviews for Maytag yet.