Maytag MGD8630H Support and Manuals
Get Help and Manuals for this Maytag item
This item is in your list!
View All Support Options Below
Free Maytag MGD8630H manuals!
Problems with Maytag MGD8630H?
Ask a Question
Free Maytag MGD8630H manuals!
Problems with Maytag MGD8630H?
Ask a Question
Popular Maytag MGD8630H Manual Pages
Installation Instructions - Page 3
...Clear the room, building, or area of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1. do not use gasoline or other appliance. - Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier from a neighbor's phone.
I Installations and repairs must be electrically grounded in accordance with local...
Installation Instructions - Page 4
...legs (4) Parts needed (steam models):
"Y" connector
2' (0.6 m) inlet hose
Caulking gun and compound (new vent installations)
Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench
Wire stripper (direct wire installations)
4
Rubber washer
5' (1.52 m) inlet hose
Parts package is located in dryer drum. Tools needed for gas connections)
1/4" (6 mm) and 5/16" (8 mm) nut driver...
Installation Instructions - Page 5
... 15 or 20 A circuit for a gas dryer or 30 A circuit for your washer's water supply by purchasing the necessary parts noted in an area where it will be exposed to the dryer must support dryer weight of dryer. The kit should be type SRD or SRDT and be installed or stored in "Parts needed."
■■ Level floor with...
Installation Instructions - Page 6
... and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH. Back view:
Recommended installation clearances (dryer only):
Water inlet
(Steam Models Only)
Vent
Gas
*Approx. Additional installation requirements: This dryer is allowed for mobile home installations. For further information, see "Assistance or Service" in door are required. Some codes limit, or do not permit...
Installation Instructions - Page 8
...
oper outlet
SAVE THESE INSTRUCTIONS
SAVE THESE INSTRUCTIONS
8 GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer must be grounded.
epresentative
or personnel if you use Power Supply Cord Replacement Part Number 8529008.
4-wire receptacle (14-30R)
For further information, please reference service numbers located in a risk of above codes standard may be grounded...
Installation Instructions - Page 9
... six (6) ft. (1.8 m) of your dryer to do not use with propane gas with the National Fuel Gas Code, ANSI Z223.1. NOTE: Pipe-joint compounds that an individual manual shut-off valve must be installed in accordance with appropriate conversion. ■■ Your dryer must be easy to the dryer. No attempt shall be installed within six (6) ft. (1.8 m) of your...
Installation Instructions - Page 17
.... A. Correct any leak found.
17 NOTE: For propane gas connections, you must be used , be different, according to dryer
A. Do not use pipe-joint compound resistant to do so can result in supply line; Open valve
Open shut-off valve. MAKE GAS CONNECTION
(Gas models only)
WARNING
2. Install a shut-off valve in death, explosion, or fire...
Installation Instructions - Page 23
... any dust.
Read "Dryer Use" in your Use and Care Guide. If you have all of your tools. Dispose of the water system, which will not start, check the following:
• Controls are on . Check for certain part replacement or repair. Over time, the buildup of lime...
Owners Manual - Page 3
... accordance with clothes dryers. Follow the gas supplier's
instructions. • If you cannot reach your gas supplier from a neighbor's phone. WARNING FIRE HAZARD Failure to follow all occupants. • Immediately call your gas supplier, call the fire department. − Installation and service must be performed by a qualified installer. − Install the clothes dryer according to...
Owners Manual - Page 8
... appearance of legs may be required, depending on your dryer. Parts Supplied (all parts are included.
Check local codes. See "Electrical Requirements" and "Venting Requirements" before purchasing parts.
Pipe-joint compound resistant to the Quick Start Guide for service contact information. Mobile home installations require metal exhaust system hardware available for contact and...
Owners Manual - Page 9
.... Mobile Home - If not level, clothes may not tumble properly and automatic sensor cycles may cause dryer not to support dryer and a total weight (dryer and load) of installation and servicing, spacing for companion appliances, and clearances for purchase from dryer. Location Requirements
WARNING
Spacing for straight-back venting only.
IMPORTANT: Do not operate your local building...
Owners Manual - Page 10
... all gas connections.
Gas Type
Natural Gas:
This dryer is properly grounded. Gas Dryer Power Hookup -
Do not remove ground prong.
Failure to connect your Quick Start Guide. SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new CSA International approved gas supply line.
Examples of gas in doubt as needed, to convert the appliance from the gas specified on the model...
Owners Manual - Page 12
... the Quick Start Guide.
2. Securely tighten all connections by brushing on threads of a qualified person include: licensed heating personnel, authorized gas company personnel, and authorized service personnel. and Canada
WARNING
Explosion Hazard Use a new CSA International approved gas supply line. Connect gas supply to dryer
A. 3/8" (9.5 mm) flexible gas connector
B. 3/8" (9.5 mm) dryer pipe...
Owners Manual - Page 13
...codes and ordinances.
NOTE: If using an existing vent system, clean lint from your Quick Start Guide.
Plan Vent System
Recommended exhaust installations:
Typical installations vent the dryer...; Must be fully extended and supported in final dryer location.
� Remove excess ...instructions can be used for best drying performance and to keep rodents and insects from ground or any gas...
Maytag MGD8630H Reviews
Do you have an experience with the Maytag MGD8630H that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Maytag yet.
Earn 750 points for your review!