Maytag MGD6630HW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGD6630HW manuals!
Problems with Maytag MGD6630HW?
Ask a Question
Free Maytag MGD6630HW manuals!
Problems with Maytag MGD6630HW?
Ask a Question
Maytag MGD6630HW Videos
Maytag Gas Dryer MGD6630HW
Duration: 1:01
Total Views: 2,350
Duration: 1:01
Total Views: 2,350
Maytag MGD6630HW Sécheuse
Duration: :43
Total Views: 1
Duration: :43
Total Views: 1
Maytag MGD6630HW Dryer
Duration: :44
Total Views: 55
Duration: :44
Total Views: 55
Popular Maytag MGD6630HW Manual Pages
Installation Instructions - Page 3
... gas supplier's
instructions.
• If you cannot reach your gas supplier from a neighbor's phone. IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.
The dryer must be listed. I Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed...
Installation Instructions - Page 4
... drum. NOTE: Do not use leveling legs supplied with dryer if installing with dryer): ■■ Vent clamps ■■ Vent elbows and vent work INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Tools needed for gas connections)
1/4" (6 mm) and 5/16" (8 mm) nut driver (recommended)
Level
Pipe-joint compound resistant to propane...
Installation Instructions - Page 5
... be exposed to bottom of 1" (25 mm) under entire dryer. If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. The wires that connect to shut off at temperatures below 40°F (4°C). Maytag® Models
IMPORTANT: Do not operate, install, or store dryer where it will be at least 18" (460 mm) above...
Installation Instructions - Page 6
...available to reduce noise transfer. measurement
NOTE: Most installations require a minimum of gas dryers:
■■ Mobile Home Installation Hold-down Kit Part Number 346764 is installed, top and bottom air openings in the top and bottom of the door are required. Check code requirements.
Mobile home installations require: ■■ Metal exhaust system hardware, available...
Installation Instructions - Page 8
... Use and Care Guide. epresentative
or personnel if you use Power Supply Cord Replacement Part Number 8529008.
4-wire receptacle (14-30R)
For further information, please reference service numbers located in doubt as to whether the dryer is equipped with Canadian Electrical Code, C22.1 -
latest edition and all local codes and ordinances. This dryer is properly grounded. CANADA...
Installation Instructions - Page 9
... Care Guide.
GAS SUPPLY LINE Option 1 (Recommended Method) Flexible stainless steel gas connector:
■■ If local codes permit, use with propane gas with appropriate conversion. ■■ Your dryer must have a qualified person make sure gas pressure does not exceed 13" (33 cm) water column.
In the U.S.A.: An individual manual shut-off valve must be installed within...
Installation Instructions - Page 10
... for leveling legs
Gas supply pressure testing ■■ The dryer must be an additional 10" (254 mm) or 15.5" (394 mm) from the floor. BURNER INPUT REQUIREMENTS Elevations above 2,000 ft. (610 m):
■■ When installed above 2,000 ft. (610 m) a 4% reduction of the burner Btu rating shown on the model/serial number plate...
Installation Instructions - Page 17
...to dryer. Install a shut-off valve
1. Open shut-off valve. Using a wrench to tighten, connect gas supply to gas ...gas company personnel, and authorized service personnel.
A. 3/8" flexible gas connector B. 3/8" dryer gas pipe
C. 3/8" to 3/8" pipe elbow D. 3/8" pipe-to-flare adapter
fitting
A combination of propane gas. Your connection may be sure there are no kinks. Connect gas...
Installation Instructions - Page 18
....
Review "...supported in death or fire. Rigid metal vent:
■■ Recommended for exhausting.
Replace plastic or metal foil vents with lint. Dryer...install in enclosed walls, ceilings, or floors. ■■ The total length should cap the vent to follow these instructions can result in final dryer location. ■■ Remove excess to seal all governing codes...
Installation Instructions - Page 19
...instructions can be securely fastened to use.
A. Bottom exhaust installation
Determine vent path: ■■ Select route that will :
■■ Shorten life of mobile home and must be converted to have the dryer... unused exhaust holes with a manufacturer's exhaust cover kit. Standard rear offset exhaust installation B.
Determine vent length and elbows needed for mobile...
Installation Instructions - Page 20
...Install Vent System
1. XXXXXXX-XXX.
Avoid 90° turns. Long Vent System Chart
Number of 90° elbows
Type of length.
2. A gas model would be DJAV - NAT - Connect vent to dryer... model has a long vent system, refer to the type code located on the serial number plate in the inner door well. Example: An electric model would be DJAV - ELE - Install exhaust hood
Install...
Installation Instructions - Page 21
...attach "Y" connector to cold water faucet. Record hose installation or replacement dates on connector.
21 The dryer must be connected to "Connect Vent." Screw on ...replace with additional 2/3 turn . Screw on coupling by hand until it is seated on connector. Using pliers, tighten the couplings an additional 2/3 turn .
CONNECT INLET HOSE (STEAM MODEL ONLY)
For non-steam models...
Installation Instructions - Page 23
... for certain part replacement or repair.
See "Level Dryer." ‰‰Remove film on console and any tape remaining on . ‰‰Check for levelness. Excessive scale buildup may lead to operate correctly.
NOTE: The dryer must be sure that all four legs are now installed. COMPLETE INSTALLATION CHECKLIST
‰‰Check that the flexible gas line is...
Installation Instructions - Page 24
... securing the door strike to do so can result in hinge. Failure to the door frame of dryer door frame with round and square-shaped doors. Move the door strike
1. Replace all parts and panels before servicing. Rotate the strike 180° and attach to remove. Disconnect wiring.
Tools needed:
ALL DOORS:
2.
Using a T25...
Instruction Sheet - Page 1
...thirds turn .
2. Remove old rubber washer from whom you purchased your dryer or an authorized service company.
2' (0.6 m) Inlet hose
CONNECT INLET HOSES
1. Turn cold ...replace with dryer)
5' (1.5 m) Inlet Hose
Your installation may require additional parts. C heck for Steam Dryers
Instrucciones para la conexión de la manguera de entrada para secadoras con vapor
Instructions...
Maytag MGD6630HW Reviews
We have not received any reviews for Maytag yet.