Makita XWT11SR1 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XWT11SR1 manuals!
Problems with Makita XWT11SR1?
Ask a Question
Free Makita XWT11SR1 manuals!
Problems with Makita XWT11SR1?
Ask a Question
Makita XWT11SR1 Videos
Popular Makita XWT11SR1 Manual Pages
XWT11 Instruction Manual - Page 2
...) power tool. A moment of flammable liquids, gases or dust. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Fastening capacities Square drive No load speed (RPM)
Impacts per minute
Standard bolt ... while operating power tools may differ from heat, oil, sharp edges or moving parts. Cluttered or
dark areas invite accidents. 2.
Keep children and bystanders away while operating...
XWT11 Instruction Manual - Page 3
...repair person using the tool in this instruction manual may cause serious personal injury. Keep handles dry, clean and free from rotating parts...parts.
7. A charger that may make a connection from the power tool before installation. 4. Have your hair, clothing, and gloves away from repeated use) replace... in moving parts. Recharge only with specifically designated battery packs...
XWT11 Instruction Manual - Page 4
...Makita warranty for maintaining maximum battery life
1. Charge the battery cartridge before installing... or removing of the button, it locks in locations where the temperature may cause them out with room temperature at 10 °C - 40 °C (50 °F - 104 °F). Overcharging shortens the battery service...installing or removing battery cartridge. Important safety instructions...
XWT11 Instruction Manual - Page 5
... voltage: The remaining battery capacity is operated in a manner that caused the tool to draw an abnormally high current.
Indicating the remaining battery capacity
Country specific
1
► 1 . This system automatically cuts off and stop during operation if the tool and/or battery are equipped with a protection system. If the tool does...
XWT11 Instruction Manual - Page 6
...
NOTE: For approximately 10 seconds after the switch trigger is released, have the tool repaired by a Makita local service center.
NOTE: When the tool is ON. Tool speed is increased by pulling the ...The LED display goes off , release it may lower the illumination. Switch trigger
CAUTION: Before installing the battery cartridge into the tool, always check to turn on , the lamp status is...
XWT11 Instruction Manual - Page 7
CAUTION: When not operating the tool, always set the reversing switch lever to the work. When the reversing switch lever is ... with pulling the trigger fully in four steps 2. This tool has a reversing switch to a complete stop mode 6. Button
Specifications of each impact force grade
Impact force grade displayed on panel
Hard
Maximum blows 3,500 min-1 (/min)
Application
Tightening when ...
XWT11 Instruction Manual - Page 8
...the square drive until the red indicator
2
cannot be sure that the tool is removed before installing the impact socket. Selecting correct impact socket
Always use it is firmly secured. An incorrect ...inaccurate and inconsistent fastening torque and/or damage to you or someone around you can be installed on the upper side of the impact socket with auto stop function. Tap it is not...
XWT11 Instruction Manual - Page 9
...impact socket
will cause a reduction in this manual. NOTE: Excessive fastening torque may result.
When... persons. Compensate by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Before starting your local Makita Service Center. • ... figures. To maintain product SAFETY and RELIABILITY, repairs, any other accessories or attachments might present a...
XWT11 Instruction Manual - Page 10
... workmanship or material, Makita will repair (or at our option, replace) without charge. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you . This Warranty does not apply where: • repairs have other rights which vary from the date of Makita's Factory or Authorized Service Centers.
XWT11 Parts Breakdown - Page 2
.... 1 PC. 1 PC. 1 PC. 2 PC. 3 PC. 1 PC. 3 PC. 1 PC. 4 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 2 PC. 1 PC. 1 PC. 1 SET 2 PC. 2 PC. 0 1 PC. 1 1 1 PC. 1 PC. Model XWT11Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
183D46-6
001 C10 263005-3
001 C20 252126-6
001 D10
002
852T91-5
003
266130-9
004
419041...
XWT11SR1 New Tool Flyers English - Page 1
...with battery 3.2 lbs. All models and accessories subject to provide improved dust and water resistance for operation in a wide range of Makita Corporation and is engineered to... Socket Set (A-96372)
All specifications subject to change without prior notice. 18V LXT® LITHIUM-ION COMPACT BRUSHLESS CORDLESS 3-SPEED 1/2" SQ. DRIVE IMPACT WRENCH KIT (2.0Ah)
NEW TOOL OVERVIEW
XWT11SR1
ALSO ...
Makita XWT11SR1 Reviews
Do you have an experience with the Makita XWT11SR1 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!