Makita XSL04ZU Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XSL04ZU manuals!
Problems with Makita XSL04ZU?
Ask a Question
Free Makita XSL04ZU manuals!
Problems with Makita XSL04ZU?
Ask a Question
Popular Makita XSL04ZU Manual Pages
XSL04 XSL06Z Instruction Manual - Page 3
...warnings, instructions, illustrations and specifications provided with...cord away from heat, oil, sharp edges or moving parts.
7. Use personal protective equipment. Do not wear loose ...power tool. It is dangerous and must be repaired.
3. Any power tool that have the switch... refers to protect your own safety, read instruction manual before connecting to rain or wet conditions. ...
XSL04 XSL06Z Instruction Manual - Page 4
...repair person using the tool, do not wear cloth work to the right of parts and any other small metal objects, that are easier to fire or temperature above 130 °C may affect the power tool's operation. If supporting the workpiece by the manufacturer or authorized service...burns.
5. Service of fire. When using only identical replacement parts. Safety instructions for lubricating ...
XSL04 XSL06Z Instruction Manual - Page 5
...you change the bevel or mitre angle setting, make certain that is bowed or ... than wood, aluminum or similar materials. Replace cracked or damaged blade immediately. Keep blade...on the tool or specified in the manual. for all moving parts to stop and disconnect the plug ...Do not use another person as additional support.
Additional instructions
1. Serious injury could cause loss of...
XSL04 XSL06Z Instruction Manual - Page 6
... EXPOSURE. Be careful not to these parts could indicate poor installation or a poorly balanced blade. 19. Damage to damage the arbor, flanges
(especially the installing surface) or bolt. Be sure that... with 21CFR 1040.10 and 1040.11 AVOID EXPOSURE-Laser radiation is emitted from this manual. While making a slide cut and release switch immediately.
11. NEVER use accessories recommended...
XSL04 XSL06Z Instruction Manual - Page 13
...workpiece is especially dirty and vision through age or UV light exposure, contact a Makita service center for a new guard. Kerf board
1
2
3
4
5
1
... and pull the carriage toward the guide fence fully and adjust the kerf ... boards will help provide proper support of the blade guard should be... follows:
1 ► 1 . NOTICE: After setting the bevel angle ensure that the kerf boards are ...
XSL04 XSL06Z Instruction Manual - Page 17
...in unintentional operation and serious personal injury. If the tool consistently fails to a Makita service center for proper repairs BEFORE further usage.
1
2
Electric brake
This tool is equipped with an ... use a lock with a negated lock-off . Lock-off button.
Switch action
WARNING: Before installing the batteries into the laser beam. WARNING: Do not use the tool if it runs when...
XSL04 XSL06Z Instruction Manual - Page 21
...support base of travel. Insert the upper fence into the hole on the upper fence to the tool and/or the workpiece. WARNING: After a cutting operation do so may result in serious personal injury. Do not rely solely on the holder.
1
2
Guide...
3
► 1 . WARNING: Before bevel-cutting, make sure that no part of the tool, especially the blade, contacts the upper and lower fences when ...
XSL04 XSL06Z Instruction Manual - Page 22
... flip the vise nut clockwise. WARNING: When cutting a thin workpiece, such as base boards, against the guide fence and the turn the vise knob clockwise. Vise nut 3. Holder 2. 1
2 3
4
►... be installed in serious personal injury.
Vise arm 2. If some part contacts the vise, re-position the vise. To secure the workpiece after setting, turn base. Proper workpiece support will ...
XSL04 XSL06Z Instruction Manual - Page 31
...following items: • A wireless unit • A vacuum cleaner which supports the wireless
activation function
The overview of the wireless activation function setting is as shown in the correct direction and the lid is inserted in ... the back of the lid will lift the wireless unit as a metal part of the tool, before installing the wireless unit. Refer to the slot and then close the lid....
XSL04 XSL06Z Instruction Manual - Page 32
... NOTE: Refer to the instruction manual of the tool, finish the tool registration beforehand. 1. If you wish to "AUTO".
► 1 . Wireless unit 2. Hook 3.
Set the stand-by switch 3....registration for the vacuum cleaner
NOTE: A Makita vacuum cleaner supporting the wireless activation function is required for the tool registration. Install the batteries to the tool before starting the...
XSL04 XSL06Z Instruction Manual - Page 33
... 2. Check if the vacuum cleaner runs while the switch trigger is blinking. In this case, set the stand-by switch on the tool again. NOTE: The vacuum cleaner starts/stops with the switch... when the vacuum cleaner detects a switch operation of the vacuum cleaner, too. Install the wireless unit to the instruction manual of the tool. To stop blinking in green after 20 seconds elapsed. NOTE:...
XSL04 XSL06Z Instruction Manual - Page 36
... of the
the slot is improperly installed into the tool.
Push the wireless...Troubleshooting for wireless activation function
Before asking for both the tool or vacuum cleaner has not finished. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs... cleaner is not installed into the tool. If you find a problem that is not set to dismantle the...
XSL04 XSL06Z Instruction Manual - Page 40
... like.
This Warranty gives you specific legal rights, and you need any trouble develop during this manual. Some states do not allow the exclusion or limitation of an accessory or attachment may result in the previously covered section titled "Blade guard". Clean the lens gently with your local Makita Service Center.
• Steel & Carbide-tipped...
XSL04ZU Parts Breakdown - Page 3
Model XSL04ZU Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
265995-6
002
183H69-8
002 C10 810483-4
002 D10
003
632L09-2
... XSL04 NAME PLATE MOTOR HOUSING TAPPING SCREW 4X18 PAN HEAD SCREW M5X50 BATTERY HOUSING SET RUBBER PIN 6 CAUTION LABEL INC. 30 BATTERY HOUSING SET RUBBER PIN 6 CAUTION LABEL INC. 29 STATOR BAFFLE PLATE TAPPING SCREW 4X18 BALL...
XSL04PTU New Tool Flyers English - Page 1
...-2)
1
2
3
All specifications subject to run cooler and...60.2 lbs. All models and accessories subject to ...Makita built electronically controlled BL™ Brushless Motor delivers 4,400 RPM for faster and smoother cutting
• The BL™ Brushless Motor eliminates carbon brushes, enabling the BL Motor to change without prior notice. UPC Code (XSL04PTU 088381-870955 UPC Code (XSL04ZU...
Makita XSL04ZU Reviews
Do you have an experience with the Makita XSL04ZU that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!