Makita XT336T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XT336T manuals!
Problems with Makita XT336T?
Ask a Question
Free Makita XT336T manuals!
Problems with Makita XT336T?
Ask a Question
Popular Makita XT336T Manual Pages
Instruction Manual - Page 4
... INSTRUCTIONS. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the tool in this
instruction manual ...replace strict adherence
to follow the safety rules stated in high locations.
6. SAVE THESE INSTRUCTIONS. WARNING:
DO NOT let comfort or familiarity with product
(gained from rotating parts...
Instruction Manual - Page 6
...set to the correct position before the tool stops may damage the tool. • When not operating the tool, always set the speed change , have the tool repaired... cartridge, cool down the tool fully. Switch action
CAUTION: • Before installing the battery cartridge into the tool,
always check to scratch the lens of ... Makita local service center.
The tool may lower the illumination.
Instruction Manual - Page 7
...the position of the tool. Select one of the counter parts on the tool body. Installing or removing driver bit or drill bit
1. Installing bit holder
1. For rotation only, turn the sleeve counterclockwise...modes suitable for a particular application. Selecting the action mode
CAUTION: • Always set the ring correctly to your work on the ring. Arrow
2
ASSEMBLY
CAUTION: ...
Instruction Manual - Page 9
... and RELIABILITY, repairs, any assistance ...manual. Use a cutting lubricant when drilling metals.
Only use gasoline, benzine, thinner, alcohol or the like. The guide screw makes drilling easier by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
9
Drilling in wood, the best results are iron and brass which should be removed simply by setting...
Instruction Manual - Page 10
...Warranty gives you specific legal rights, and you . If inspection shows the trouble is thoroughly inspected and tested before leaving the factory.
This Warranty does not apply where:
repairs have been made...may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. It is warranted to be free of defects from ...
XDT14 Instruction Manual - Page 3
... sharp and clean. Follow instruction for your power tool serviced by insulated gripping surfaces, when performing an operation where the fastener may cause irritation or burns.
volts
direct current
no one is in this instruction manual may cause burns or a fire.
4. 2. Ensure the switch is below when using only identical replacement parts. This enables better control...
XDT14 Instruction Manual - Page 6
...overheated, the light flashes for counterclockwise rotation.
CAUTION: When not operating the tool, always set the reversing switch lever to quickly stop .
When the lamp does not come on ... tool before operating again.
NOTE: When the tool is released, have the tool serviced at a Makita service center. CAUTION: Use the reversing switch only after releasing the switch trigger. When ...
XDT14 Instruction Manual - Page 10
...you need any trouble develop during this manual. They may differ from the date of original purchase. If inspection shows the trouble is caused by others: • repairs are recommended ...use with your local Makita Service Center. • Driver bits • Socket bits • Hook • Plastic carrying case • Battery protector • Tool hanger • Makita genuine battery and ...
XDT14 Parts Breakdown - Page 2
Model XDT14M/R/Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
183E36-5
001 C10 263005-3
001 C20 252126-6
001 D10...
040
652069-6
041
620545-8
041 D10
042
809R92-2
A01
266622-8
A02
346449-3
A03
450128-8
A04
***DC18RC
HOUSING SET RUBBER PIN 6 HEX. LOCKING NUT M4-7 INC. 1 SWITCH PLATE COMPLETE REAR COVER TAPPING SCREW 3X16 TAPPING SCREW...
Makita DC18RC Instruction Manual - Page 3
...Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 - 60 HZ
D.C. 7.2 V - 18 V
0.88 kg (1.94 lbs)
0.77 kg (1.70 lbs)
• Manufacturer reserves the right to change specifications...damaged, ask Makita authorized
service center to replace it within...THESE INSTRUCTIONS - This manual contains important safety and operating instructions ...not attempt to the guide of charger
can ...
XRJ07 Instruction Manual - Page 2
... operating power tools may differ from heat, oil, sharp edges or moving parts. There is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply...an extension cord suitable for appropriate conditions will reduce personal injuries.
3. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XRJ07
Length of electric shock.
7. Failure to country.
• The weight ...
XRJ07 Instruction Manual - Page 3
...repaired before making any other BATTERY packs may affect the power tool's operation. in moving parts.
7. Slippery handles and grasping surfaces do not allow persons unfamiliar with another practical way to secure and support...service damaged BATTERY packs. Follow instruction for operations different from injury when using only identical replacement parts...with specifically designated ...
XRJ07 Instruction Manual - Page 4
.... 13. Use the batteries only with any conductive material.
(2) Avoid storing battery cartridge in this instruction manual may be toxic. CAUTION: Only use a damaged battery.
10.
Charge the battery cartridge before charging it cannot move around in a fire.
8. Overcharging shortens the battery service life.
3. Let a hot battery cartridge cool down before completely discharged.
XRJ07 Instruction Manual - Page 8
...; the tool has been abused, misused or improperly
maintained: • alterations have other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. This Warranty gives you specific legal rights, and you .
8 ENGLISH NOTICE: Never use accessory or attachment for its stated purpose. THIS DISCLAIMER APPLIES BOTH DURING...
XT336T New Tool Flyers English - Page 1
... the charging process to stock on the charger
SPECIFICATIONS
Tool Count 3 Voltage 18V Battery 18V LXT® Lithium-Ion Battery Charge Time (minutes 45 UPC Code 088381-873246
STANDARD EQUIPMENT
• 18V LXT® Brushless 1/2" Hammer Driver-Drill (XPH07Z) • 18V LXT® Brushless 3-Speed Impact Driver (XDT14Z) • 18V LXT® Sub-Compact...
Makita XT336T Reviews
We have not received any reviews for Makita yet.