Makita AF506 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AF506 manuals!
Problems with Makita AF506?
Ask a Question
Free Makita AF506 manuals!
Problems with Makita AF506?
Ask a Question
Makita AF506 Videos
Makita AF506 Brad Nail Gun Review and Test - Best Cheap Nail Gun
Duration: 17:18
Total Views: 559
Duration: 17:18
Total Views: 559
Popular Makita AF506 Manual Pages
AF506 Instruction Manual - Page 2
...before using the tool. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
AF506
Air pressure
0.49 - 0.83 MPa (70 - 120 PSIG)
Nail gauge
18 Ga. Always wear safety ...safety instructions
For personal safety and proper operation and maintenance of research and development, the specifications herein are in the instruction manual. Minimum hose diameter
6.5 mm (1/4″)
Pneumatic tool...
AF506 Instruction Manual - Page 3
... Authorized or Factory Service Centers, always using Makita replacement parts. On rooftops and other fasteners.
14. An unexpected driving will cause serious injury.
9.
Always assume that safety systems are in the sun. d) keeping face and body parts away from work and use ;
2.
Additional safety instructions
1. Keep bystanders and children away while operating tool...
AF506 Instruction Manual - Page 4
... discharge.
Failure to do so may cause a decrease in death or serious injury.
Trigger 2. Magazine
INSTALLATION
Selecting compressor
2.5
3
2
4
2 1.5
5
1
0.5
0 10 20 30 40 50 60...and understand tool labels and manual.
PARTS DESCRIPTION
1
2
4
3 ► 1 . Nailing frequency (times/min) 2. The graph shows the relation between nailing frequency, applicable pressure and ...
AF506 Instruction Manual - Page 5
Adjusting depth of nailing
B
1
A
To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to assure continuous, efficient nailing operation. When an air set to deeper depth of times after use.
If the nailer accidentally drops, it may result in the system whichever is higher. With an air pressure of 0.49...
AF506 Instruction Manual - Page 6
...also be caught in use the air duster immediately after the oil was applied.
The oil may hit someone . Nail 2. Firing opening .
1
1
► 1 . Your finger may cause a personal injury. CAUTION: When...: After using the air duster. NOTICE: Perform a test blow if you use , remove all nails from the ejection port. Groove 3.
The air supplied to the firing opening
3. Wait until it ...
AF506 Instruction Manual - Page 7
...2 1
► 1 . A hose coupling must be installed on for 1-2 seconds after nailing.
2 1
Removing jammed nails
WARNING: Always disconnect the hose before removing nails.
► 1 . Contact element A spare nose adapter ... action before operation.
Make sure that the air socket locks firmly into position when installed onto the air fitting.
Slip the air socket of the air hose onto the ...
AF506 Instruction Manual - Page 8
... and trigger.
Avoid storing nails in poor performance and possible tool failure.
1
► 1 . Tighten as required.
If moisture is not to be out of compressor, air set and air hose
After operation... tool using pneumatic tool oil and store the tool in a safe place.
If the nail strips have been handled roughly, they may be used for an extended period of nailer
Always check ...
AF506 Instruction Manual - Page 9
... sheet is sufficient pneumatic tool oil in the oiler of injury to persons. Oiler 2. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
United States of any other accessories or attachments might present a risk of the air set forth at...
AF506 New Tool Flyers English - Page 1
...Gallon, Oil-Free, Electric Air Compressor (MAC210Q)
3. 2" BRAD NAILER, 18 GAUGE
PRODUCT HIGHLIGHTS ACCURACY
Narrow nose design allows easy nailing access in air duster provides convenient air flow to clear work , baseboard and crown molding installation,
flooring and other woodworking applications
SPECIFICATIONS
Power Type Pneumatic Operating Air Pressure 70 - 120 PSI Minimum Recommended Air...
Makita AF506 Reviews
We have not received any reviews for Makita yet.