Makita XRU23SM1 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XRU23SM1 manuals!
Problems with Makita XRU23SM1?
Ask a Question
Free Makita XRU23SM1 manuals!
Problems with Makita XRU23SM1?
Ask a Question
Popular Makita XRU23SM1 Manual Pages
XRU23 Instruction Manual - Page 2
...WARNINGS
Important safety instructions
WARNING: When using the battery adapter, read the instruction manual.
3. It is in the...with the switch on your region of residence. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Type of handle No load speed
XRU23
Loop handle
2:... are shown in the off position before installing the battery pack. Never allow people unfamiliar...
XRU23 Instruction Manual - Page 3
...switch trigger when
not operating the tool and when moving parts. it away from the battery; They can make a... starting the machine accidentally.
4. Carrying the machine with specifically designated battery packs. Shorting the battery terminals together may cause... range may exhibit unpredictable behaviour resulting in the instructions. Ensure the switch is suitable for cutting grass...
XRU23 Instruction Manual - Page 4
...manual.
4. A guard or other part... repaired or replaced ...replacement parts. Check with damaged guards or without guards in this may make sure that is switched off the motor and inspect the nylon cutting head.
9. This will ensure that it will revolve when starting make exposed metal parts of operation
1. Check for use . Before starting .
6. Only use the tool in the instructions...
XRU23 Instruction Manual - Page 5
... hard object to do this type of debris.
9. WARNING: Use of this instruction manual may result in inferior performance and shorten the life of the item being shipped, ... and herbicides. by our authorized service center.
8. 21. Check for tool. Use only the manufacturer's recommended replacement parts and accessories.
7. Have the tool repaired only by third parties, forwarding agents...
XRU23 Instruction Manual - Page 6
.... Installing the batteries to disposal of the battery cartridge. Do not allow chips, dust, or soil stuck into the terminals, holes, and grooves of battery. 12. Unless the tool supports the use near high-voltage electrical power lines. It may result in a fire, excessive heat, explosion, or leak of it .
4. SAVE THESE INSTRUCTIONS...
XRU23 Instruction Manual - Page 8
...button, it may accidentally fall out of the cartridge. If you . CAUTION: Always install the battery cartridge fully until it locks in serious personal injury from the tool while ...1
3
Tool / battery protection system
The tool is equipped with a little click. Red
Over-
Installing or removing battery cartridge
CAUTION: Always switch off power to the motor to resume. CAUTION: Hold the ...
XRU23 Instruction Manual - Page 9
... the switch trigger actuates properly and returns to our authorized service center for tool or battery
When the tool or battery cartridge...
1
2
► 1 . Overheat protection for proper repairs BEFORE further usage. To turn on the main power button .... Indicator lamps 2. Indicator lamps 2.
CAUTION: Before installing the battery cartridge into the tool, always check to...
XRU23 Instruction Manual - Page 10
... stop .
1
Electric brake
This tool is not a substitute for a certain period without the protector. Installing main components
2
► 1 . CAUTION: This brake system is equipped with the stopper hole in ... installed all the main components. Stopper hole 3. If the tool consistently fails to switch off and battery cartridge is released, have the tool serviced at our service center...
XRU23 Instruction Manual - Page 12
... Cutter
Installing the cutting tool
CAUTION: Always use genuine Makita nylon cutting head.
1.
The cutting tool is fully inserted.
► 1 . Spindle 2. Failure to do so can replace the ...Motor housing 3. Hex wrench 12 ENGLISH Set the angle and position of the cutting tool(s) supplied as shown in the figure, and then tighten the bolt.
1
Installing the protector
WARNING: Never use the ...
XRU23 Instruction Manual - Page 13
...
When using a nylon cutting head (bump & feed type) The nylon cutting head is damaged, replace it securely by hand.
4
1
3 2
► 1 . Most effective cutting area 13 ENGLISH... NOTE: The holes in serious personal injury. To remove the nylon cutting head, follow the installation procedures in one area. To feed out the nylon cord, tap the cutting head against the ground while...
XRU23 Instruction Manual - Page 14
... .
Cleaning the tool
Clean the tool by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Replacing the nylon cord
WARNING: Use only the nylon cord with a dry...repairs, any more. Failure to do so may result. NOTICE: The bump feed will not operate properly if the nylon cutting head is secured to the housing properly as described in this instruction manual...
XRU23 Instruction Manual - Page 17
...
Cutting tool is dropping. Remedy Install the battery cartridge. Recharge the battery. Stop using Makita replacement parts for more details regarding these accessories, ask your local authorized service center for use of injury to this manual.
Replace the cutting tool. CAUTION: These accessories or attachments are recommended for repair.
State of America: www.makitatools...
New Tool Flyers English - Page 1
Net Weight (without prior notice. All models and accessories subject to protect against
overloading, over-discharging and over-heating
SPECIFICATIONS
Cutting Swath 13" No Load Speed (var. 2...Weight 12.46 lbs. (XRU23SM1) Shipping Weight 9.46 lbs. (XRU23Z) UPC Code 088381-730358 (XRU23SM1) UPC Code 088381-730358730310 (XRU23Z)
STANDARD EQUIPMENT
XRU23SM1 • 18V LXT® Brushless 13...
XRU23Z Parts Breakdown - Page 3
XRU23 Tech Bulletin
Part No. SOCKET HEAD BOLT M5X10
2
1 021 251513-6
H.S.H.BOLT M5X25
2
1 022 347734-7
PROTECTOR CLAMP
1
1 ... HEAD BOLT M5X12
1
1 031 347011-7
PIPE CLAMP 29
1
1 032 699157-8
POWER SUPPLY CORD UNIT
1
1 036 183R55-9
GRIP HOUSING SET
1
1 037 140W41-3
SWITCH CIRCUIT COMPLETE
1
1 038 651494-8
SWITCH C3JW-1A-PA-2
1
1 039 233101-1
COMPRESSION SPRING 4
1
Notes...
XRU23Z Parts Breakdown - Page 4
...
1
1 041 459758-2
SWITCH LEVER
1
1 042 233622-3
TORSION SPRING 12
1
1 043 266326-2
TAPPING SCREW 4X18
8
1 044 183R55-9
GRIP HOUSING SET
1
1 046 620D78-7
CONTROLLER
1
1 048 644809-6
TERMINAL
1
Notes
INC. 36
rev 0_11/13/20
4
Part No. No. XRU23 Tech Bulletin
1 XRU23
Unit Complete
Products with multiple versions are listed in subsiding order with the...
Makita XRU23SM1 Reviews
Do you have an experience with the Makita XRU23SM1 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!