Makita RT0701CX3 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita RT0701CX3 manuals!
Problems with Makita RT0701CX3?
Ask a Question
Free Makita RT0701CX3 manuals!
Problems with Makita RT0701CX3?
Ask a Question
Makita RT0701CX3 Videos
Makita 1-1/4 HP Compact Router - RT0701CX3
Duration: 2:20
Total Views: 160
Duration: 2:20
Total Views: 160
Popular Makita RT0701CX3 Manual Pages
Owners Manual - Page 2
... your mains-operated (corded) power tool or battery-operated (cordless) power tool. Use of electric shock.
Do not abuse the cord. If devices are provided for the connection of dust extraction and collection facilities, ensure these are subject to change without notice.
• Specifications may differ from heat, oil, sharp edges or moving parts. Do not use an...
Owners Manual - Page 3
...the correct
power tool for misalignment or binding of moving parts, breakage of the power tool is in a hazardous situation. Check for your power tool serviced by your extension cord is maintained. 25. An undersized cord will ensure that cannot be controlled with the power tool or these instructions, taking into account the working conditions and the work by a qualified repair person...
Owners Manual - Page 4
...workpiece.
14. Always use ) replace strict adherence
to operate because of the tool.
17. USD201-2
Symbols
The followings show the symbols used for tool. ･ volts
･ ... to follow the safety rules stated in this
instruction manual may cause cracks in the tool, always check to get fine finish, because ...installed bit.
11.
Possible to see that could burn your skin.
15.
Owners Manual - Page 5
... or by turning the speed adjusting dial to a given number setting from the top of number 1. OPERATION
Set the tool base on the dial and the approximate tool speed. Tighten
1
2.
To remove the bit, follow the installation procedure in the direction of the bit in tool malfunction.
• The speed adjusting dial can be selected for...
Owners Manual - Page 6
...progressively deeper bit settings. Base protector
1
2. Straight bit 2. The distance (X) can be cut a slightly different size
from the templet. Templet 4. Before beginning the cut on the actual workpiece, it is effectively used for the distance (X) between the router bit and the outside diameter of the templet guide router bit diameter) / 2
Straight guide (optional accessory...
Owners Manual - Page 7
...
001993
For cutting circles between the side of bit) are as a guide against the trimmer
base. Feed the tool in the figures. A
001994
NOTE: • Circles between 172 mm (6-3/4") and 186 mm
(7-5/16") in radius.
1. Min. Install the trimmer guide on the straight guide and adjust the distance between the center of circle and the...
Owners Manual - Page 10
...setting nut 5. Stopper block 8. Lower the stopper pole until it with the "0" graduation. Minute depth adjustments can be used according to lock the tool body. Offset base plate 2
1. Bar type grip
(optional
1
accessory)
011986
When using as a router... as a router, install the tool on the grip attachment and secure it makes contact with
both hands.
1. To install the knob type...
Owners Manual - Page 11
... make a sample cut can fasten the stopper pole firmly.
Set the tool base on the right side in the feed direction.
1
4
2
3
2 4
1. This will look as well as enable you can be obtained by both grip during operation. Wing bolts
011988
Install the straight guide on and wait until the bit attains full speed. Then...
Owners Manual - Page 12
.... bit diameter) / 2
Dust nozzle sets (optional accessory) For the trimmer base
011851
The templet guide provides a sleeve through which the bit passes, allowing use it as a guide against the router base. To install the templet guide, loosen the screws on the templet and move the tool with the straight guide flush
with the templet guide sliding along the side...
Owners Manual - Page 13
...manual. The use of any assistance for use with your local Makita Service Center. • Straight & groove forming bits • Edge forming bits • Laminate trimming bits • Straight guide assembly • Trimmer guide... that protrusion on the tool base using Makita replacement parts. Only use gasoline, benzine, thinner, alcohol or the like. Replace when they wear down to...
Owners Manual - Page 14
... WARRANTY. This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. • Templet guide • Collet cone 1/4" • Collet cone 3/8" • Wrench 13 • Wrench 22 • Dust nozzle set
NOTE: • Some items in...
Parts Breakdown - Page 2
...
1
A09
324378-0 ROLLER 11
1
A09
341136-9 HOOK
1
A09
941151-9 FLAT WASHER 6
1
A10
196094-2 PLUNGE BASE SET
1
A10
COMPO-PARTS
0
A11
196092-6 TILT BASE SET
1
A11
COMP0-PARTS
0
A12
153489-2 GRIP 36 COMPLETE
1
A13
195564-8 GUIDE HOLDER SET
1
A13
252649-4 THUMB NUT M6
1
A13
256850-3 ROD 8
2
A13
266339-3 CAP SQUARE NECK BOLT M6X20
1 41
227262-7 SPUR GEAR...
Parts Breakdown - Page 3
A14
831327-5 TOOL BAG
1
A15
196093-4 OFFSET BASE SET
1
A15
222171-5 PULLEY 12-23.1
1
A15
318685-1 GRIP ATTACHMENT
1
A15
912112-6 COUNTERSUNK HEAD SCREW M4X10
2
A15
COMPO-PARTS
0
Flyer (English) - Page 1
1-1/4 HP* compact router kit
POWERFUL 1-1/4 HP* MOTOR DELIVERS IMPROVED PERFORMANCE • Variable Speed Control Dial (10,000 - 30,000 RPM) Enables User to Match the
Speed to the Application • Smooth Rack-and-Pinion Fine Depth Adjustment System for More Precise
Settings • Slim and Ergonomically Designed Body for Increased Comfort and Control • Quick Release Cam Lock...
Flyer (English) - Page 2
....,La Mirada,CA 90638
"The Makita Teal color is the registered trade dress of ROUTER accessories. 1-1/4 HP* COMPACT ROUTER KIT
Model RT0701CX3
FEATURES & BENEFITS
n Powerful 1-1/4 HP* motor delivers improved performance
n Soft start feature for smooth start ups
n High visibility base design for improved handling and performance
n Base can be removed quickly to install other bases (plunge, tilt...
Makita RT0701CX3 Reviews
We have not received any reviews for Makita yet.