Owners Manual
Page 1
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com Angle Drill 13 mm (1/2") MODEL DA4000LR DOUBLE INSULATION 003009 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. www.makitatools.com Angle Drill 13 mm (1/2") MODEL DA4000LR DOUBLE INSULATION 003009 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using.
Owners Manual
Page 2
..., and visitors away while operating a power tool. SPECIFICATIONS Model Capacities No load speed (RPM) Overall length Net weight Steel Wood High Low DA4000LR 13 mm (1/2") 38 mm (1-1/2") 0 - 900/min. 0 - 400/min. 413 mm (16-1/4") 3.7 kg (8.1 lbs) • Manufacturer reserves the right to change specifications without notice. • Specifications may ignite the dust or fumes. 3. Electrical Safety 4. Failure to follow all instructions. If it still does...
..., and visitors away while operating a power tool. SPECIFICATIONS Model Capacities No load speed (RPM) Overall length Net weight Steel Wood High Low DA4000LR 13 mm (1/2") 38 mm (1-1/2") 0 - 900/min. 0 - 400/min. 413 mm (16-1/4") 3.7 kg (8.1 lbs) • Manufacturer reserves the right to change specifications without notice. • Specifications may ignite the dust or fumes. 3. Electrical Safety 4. Failure to follow all instructions. If it still does...
Owners Manual
Page 3
... eliminates the need for appropriate conditions. Replace damaged cords immediately. Personal Safety 9. Always wear eye protection. Store idle tools out of reach of the tool in any other untrained persons. Keep cutting tools sharp and clean. Tool Use and Care 15. Remove adjusting keys or wrenches before plugging in the hands of drugs, alcohol, or medication. These cords are dangerous in . Keep your 3 Be sure switch is...
... eliminates the need for appropriate conditions. Replace damaged cords immediately. Personal Safety 9. Always wear eye protection. Store idle tools out of reach of the tool in any other untrained persons. Keep cutting tools sharp and clean. Tool Use and Care 15. Remove adjusting keys or wrenches before plugging in the hands of drugs, alcohol, or medication. These cords are dangerous in . Keep your 3 Be sure switch is...
Owners Manual
Page 4
... in a risk of cord in the Maintenance section of power and overheating. Follow instructions in feet 25 ft. 50 ft. 100 ft. 150 ft. When servicing a tool, use one tool, may become hazardous when used on cord length and nameplate ampere rating. An undersized cord will draw. Accessories that may create a risk of electric shock or injury. Use of unauthorized parts or failure to carry...
... in a risk of cord in the Maintenance section of power and overheating. Follow instructions in feet 25 ft. 50 ft. 100 ft. 150 ft. When servicing a tool, use one tool, may become hazardous when used on cord length and nameplate ampere rating. An undersized cord will draw. Accessories that may create a risk of electric shock or injury. Use of unauthorized parts or failure to carry...
Owners Manual
Page 5
... high locations. 3. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to prevent dust inhalation and skin contact. Do not touch the drill bit or the workpiece immediately after operation; Contact with product (gained from rotating parts. 5. Do not leave the tool running. they may contact hidden wiring or its own cord. Operate the tool only when hand-held. 6. SPECIFIC SAFETY RULES USB001-2 DO NOT let...
... high locations. 3. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to prevent dust inhalation and skin contact. Do not touch the drill bit or the workpiece immediately after operation; Contact with product (gained from rotating parts. 5. Do not leave the tool running. they may contact hidden wiring or its own cord. Operate the tool only when hand-held. 6. SPECIFIC SAFETY RULES USB001-2 DO NOT let...
Owners Manual
Page 6
SYMBOLS USD201-2 The followings show the symbols used for tool. V volts A amperes n no load speed Class II Construction Hz hertz alternating current .../min revolutions or reciprocation per minute 6
SYMBOLS USD201-2 The followings show the symbols used for tool. V volts A amperes n no load speed Class II Construction Hz hertz alternating current .../min revolutions or reciprocation per minute 6
Owners Manual
Page 7
... the tool comes to a complete stop . 1 A B 1. Release the switch trigger to change the direction of rotation before the tool stops may damage the tool. Changing the direction of rotation. To start the tool, simply pull the switch trigger. Reversing switch lever 003029 Reversing switch action This tool has a reversing switch to stop . Move the reversing switch lever to ensure operating safety. 7 Installing side grip (auxiliary handle) CAUTION: • Always use the side grip and hold it with both hands to...
... the tool comes to a complete stop . 1 A B 1. Release the switch trigger to change the direction of rotation before the tool stops may damage the tool. Changing the direction of rotation. To start the tool, simply pull the switch trigger. Reversing switch lever 003029 Reversing switch action This tool has a reversing switch to stop . Move the reversing switch lever to ensure operating safety. 7 Installing side grip (auxiliary handle) CAUTION: • Always use the side grip and hold it with both hands to...
Owners Manual
Page 8
Drill chuck 003066 2 Installing or removing angle attachment The angle head has a spindle on the angle housing. For lower speed operation, attach the drill chuck to the end marked "HIGH". The lower speed is best utilized for drilling larger diameter holes. 003067 The tool is convenient. 1 1. To change to the "LOW" speed, proceed as follows: To remove the drill chuck, first open the chuck jaws completely and place the chuck key in one of it...
Drill chuck 003066 2 Installing or removing angle attachment The angle head has a spindle on the angle housing. For lower speed operation, attach the drill chuck to the end marked "HIGH". The lower speed is best utilized for drilling larger diameter holes. 003067 The tool is convenient. 1 1. To change to the "LOW" speed, proceed as follows: To remove the drill chuck, first open the chuck jaws completely and place the chuck key in one of it...
Owners Manual
Page 9
... drill chuck and the bolt are fitted perfectly. Socket 4. Bolt 1 2 003070 34 5 6 7 For higher speed operation 1. Spindle 5. For higher speed operation, fit the angle housing marked "LOW" to the desired position. CAUTION: • Be sure to the spindle so that they can be removed together. 1. Angle housing 2. Low 6. High 7. For lower speed operation, fit the angle housing marked "HIGH" to persons. 9 Joint 3. Then install the...
... drill chuck and the bolt are fitted perfectly. Socket 4. Bolt 1 2 003070 34 5 6 7 For higher speed operation 1. Spindle 5. For higher speed operation, fit the angle housing marked "LOW" to the desired position. CAUTION: • Be sure to the spindle so that they can be removed together. 1. Angle housing 2. Low 6. High 7. For lower speed operation, fit the angle housing marked "HIGH" to persons. 9 Joint 3. Then install the...
Owners Manual
Page 10
... tighten clockwise. After using the chuck key, be converted to the spindle so that the two faces are 1 fitted perfectly. Place the chuck key in just one hole, then loosen the chuck by hand. Drill chuck 2. Chuck key 1 003073 The tool may be sure to return to tighten all three chuck holes evenly. 003072 Slide the drill chuck to a conventional straight drive drill by installing the drill chuck without the angle attachment. 2 1. Drill chuck 4. Spindle 1. Chuck key 003055 1 Installing or removing drill bit To install...
... tighten clockwise. After using the chuck key, be converted to the spindle so that the two faces are 1 fitted perfectly. Place the chuck key in just one hole, then loosen the chuck by hand. Drill chuck 2. Chuck key 1 003073 The tool may be sure to return to tighten all three chuck holes evenly. 003072 Slide the drill chuck to a conventional straight drive drill by installing the drill chuck without the angle attachment. 2 1. Drill chuck 4. Spindle 1. Chuck key 003055 1 Installing or removing drill bit To install...
Owners Manual
Page 11
... handle) should be removed simply by pulling the bit into the workpiece. Hold the tool firmly and exert care when the bit begins to break through the workpiece. • A stuck bit can be drilled dry. The guide screw makes drilling easier by setting the reversing switch to reverse rotation in material that may back out abruptly if you suspect contains hidden nails or...
... handle) should be removed simply by pulling the bit into the workpiece. Hold the tool firmly and exert care when the bit begins to break through the workpiece. • A stuck bit can be drilled dry. The guide screw makes drilling easier by setting the reversing switch to reverse rotation in material that may back out abruptly if you suspect contains hidden nails or...
Owners Manual
Page 12
... accessories or attachments are recommended for use accessory or attachment for more details regarding these accessories, ask your Makita tool specified in the holders. Drill bits Chuck key Side grip Extension attachment Depth guage assembly Hex wrench 5 Plastic carrying case 12 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be replaced at the same time. Replace when they wear down to remove the brush holder caps. Brush holder cap 2. If you need...
... accessories or attachments are recommended for use accessory or attachment for more details regarding these accessories, ask your Makita tool specified in the holders. Drill bits Chuck key Side grip Extension attachment Depth guage assembly Hex wrench 5 Plastic carrying case 12 To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be replaced at the same time. Replace when they wear down to remove the brush holder caps. Brush holder cap 2. If you need...
Owners Manual
Page 13
Cut Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First-Class Postage Required Post Office will not deliver without proper postage. Fold 13
Cut Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 First-Class Postage Required Post Office will not deliver without proper postage. Fold 13
Owners Manual
Page 14
... PORTION Your answers to the following questions are : Design Features Size Price Makita Brand Repair Service Durability Power Other ( ) 5. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( 3. How did you ...Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 4. Any comments: Paste Paste Paste Paste Paste Paste Paste Paste DATE PURCHASED MONTH DAY YEAR MODEL NO. LAST NAME / COMPANY NAME STREET ADRESS CITY STATE ZIP CODE...
... PORTION Your answers to the following questions are : Design Features Size Price Makita Brand Repair Service Durability Power Other ( ) 5. This product was purchased from: Home Center Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply Other ( 3. How did you ...Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 4. Any comments: Paste Paste Paste Paste Paste Paste Paste Paste DATE PURCHASED MONTH DAY YEAR MODEL NO. LAST NAME / COMPANY NAME STREET ADRESS CITY STATE ZIP CODE...
Owners Manual
Page 15
... Purchased Dealer's Name & Address Model No. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. West Allis, WI 53227 (414) 541-4776 CUSTOMER'S RECORD When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to the outside... Providence Hwy. Omaha, NE 68127 (402) 597-2925 NEVADA 3375 S. Suites. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 NEW JERSEY 251 Herrod Blvd. Serial No. 15
... Purchased Dealer's Name & Address Model No. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. West Allis, WI 53227 (414) 541-4776 CUSTOMER'S RECORD When you need service: Send complete tool (prepaid) to one of the Makita Factory Service Centers listed, or to the outside... Providence Hwy. Omaha, NE 68127 (402) 597-2925 NEVADA 3375 S. Suites. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 NEW JERSEY 251 Herrod Blvd. Serial No. 15
Owners Manual
Page 16
... INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to state. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
... INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to state. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
Parts Breakdown
Page 2
... WASHER, LS0711Z BALL BEARING 608LLB, 9227C BAFFLE PLATE, DA4000LR T. SCREW FLANGE PT5X50,HR2010 FIELD 115V, 6304LR SUPPORT CPL., 6304LR CARBON BRUSH CB-303 SET, 9227C CARBON BRUSH SET CB-303, 9227C BRUSH HOLDER CAP, HM1100C MAKITA LABEL, DA3010F MOTOR HOUSING,6304LR MAKITA LABEL, DA3010F NAME PLATE, DA4000LR SWITCH, DA4000LR STRAIN RELIEF, 4323K TAPPING SCREW 4X18, 4323K CORD GUARD 8, HM0810B CORD GUARD, 6304LR CORD (2X18X8 SJ), HR2400 HANDLE COVER, DA4000LR TAPPING SCREW 4X18, 4323K JOINT CPL., DA4000LR H.S.H. BOLT M8X35, DA4000LR SOCKET, DA4000LR GEAR SHAFT L, DA4000LR KEY...
... WASHER, LS0711Z BALL BEARING 608LLB, 9227C BAFFLE PLATE, DA4000LR T. SCREW FLANGE PT5X50,HR2010 FIELD 115V, 6304LR SUPPORT CPL., 6304LR CARBON BRUSH CB-303 SET, 9227C CARBON BRUSH SET CB-303, 9227C BRUSH HOLDER CAP, HM1100C MAKITA LABEL, DA3010F MOTOR HOUSING,6304LR MAKITA LABEL, DA3010F NAME PLATE, DA4000LR SWITCH, DA4000LR STRAIN RELIEF, 4323K TAPPING SCREW 4X18, 4323K CORD GUARD 8, HM0810B CORD GUARD, 6304LR CORD (2X18X8 SJ), HR2400 HANDLE COVER, DA4000LR TAPPING SCREW 4X18, 4323K JOINT CPL., DA4000LR H.S.H. BOLT M8X35, DA4000LR SOCKET, DA4000LR GEAR SHAFT L, DA4000LR KEY...