Makita AT2550A Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AT2550A manuals!
Problems with Makita AT2550A?
Ask a Question
Free Makita AT2550A manuals!
Problems with Makita AT2550A?
Ask a Question
Popular Makita AT2550A Manual Pages
Owners Manual - Page 2
...tool with fasteners when any power source other than that the tool contains fasteners.
(2) Do not point the tool...tool operating/safety instructions.
6. ENGLISH
SPECIFICATIONS
Model
AT1150A
AT2550A
Air pressure
65 - 120 PSIG (4.4 - 8.3 bar)
Applicable staples
25 mm - 50 mm (1" - 2")
Staple...of the tool, read this instruction manual carefully before using the tool.
2. General Tool Handling ...
Owners Manual - Page 3
... leave it to use of the ordinary with the tool. Be sure that can perform stapling operations with staples unloaded and the contact element in working correctly.
33. When the air hose is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Handle the tool carefully, as instructed in the vicinity. Do not attempt to a source...
Owners Manual - Page 4
...) or 150 percent of the tool. Adjust the oiler so that has ample pressure and air output to assure cost-efficient operation.
To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to assure continuous, efficient stapling operation. Compressor air output per minute
INSTALLATION
Selecting compressor
(ft 3/min.)
5 4 3 2 1
007309...
Owners Manual - Page 5
... then slide the depth adjusting plate up or down. Select staples suitable for hanging the tool temporarily.
For proper lubrication, the tool must be driven deep enough, slide the adjusting plate in the direction of arrow as shown in this instruction
manual. FUNCTIONAL DESCRIPTION
CAUTION: • Always disconnect the hose before and after adjusting.
5 Pusher...
Owners Manual - Page 6
... hose onto the air fitting on the stapler.
Replace the trigger part with excessive force. Keep depressing the pusher until it . Insert strip of recoil. Pusher
1
3
007198
1. No. 2 method is allowed to drive a staple carefully and very accurately.
2
Slip the air socket of staples can be installed on for intermittent stapling, when you may place the contact...
Owners Manual - Page 7
... the latch on two hooks of driver guide by Makita Authorized or Factory Service Centers. Exhaust cover 1
Place the latch spring on the top of the driver guide and return it .
007206
1. Direction of staple driver has worn, staple jamming
and shallow driving will tend to its overall condition and loose screws before removing staplers. Latch
1
CAUTION: • If the...
Owners Manual - Page 8
... 60°C, over 140°F), away from sharp edges and areas which it may result in poor performance and possible tool failure. Failure to maintain sufficient lubrication will cause O-rings to the hose.
004320
Maintenance of compressor, air set . Hoses must also be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
004318
1.
Owners Manual - Page 9
... rights which vary from the date of Makita's Factory or Authorized Service Centers. This Warranty gives you specific legal rights, and you .
9 This Warranty does not apply where:
• repairs have been made to state. EN0006-1
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: • repairs are required because of normal wear...
Parts Breakdown - Page 1
...-0811 DRIVER GUIDE 59 K0700-5131 DRIVER GUIDE COVER SET 60 A0719-0981 STOPPER
87 A0913-0011 HEX.
DESCRIPTION
QTY
B0000-0301 SCREW SET M5*25 2 K0300-3471 TOP CAP SET 3 ...SET
6 A0105-0081 SPRING PLATE 7 A0301-1231 CAP, MAIN BODY
37 A0000-0061 SCREW M5*12 38 A0712-1421 HOLDER
68 A0711-2411 CONTACT ARM 69 A0714-0501 SAFETY ELEMENT
8 A0004-0001 HEX. Parts List For Wide Crown Stapler AT2550A...
Flyer (English) - Page 1
MEDIUM & WIDE CROWN STAPLERS
MEDIUM & WIDE CROWN STAPLERS FEATURE LIGHTWEIGHT DESIGN FOR COMFORT AND CONTROL
Top-Loading Magazine Allows User to Quickly Load 16 GA Staples Varying in Length from 1'' to 2'' "Tool-less" Nail Jam Clearing Minimizes Downtime Built-in Air Filter Minimizes Dust and Debris from Entering Tool Hook Allows Tool to Remain Close-by but Never in the Way...
Flyer (English) - Page 2
MEDIUM & WIDE CROWN STAPLERS
Models AT1150A / AT2550A
FEATURES & BENEFITS
I Lightweight design for comfort and control I Rugged aluminum magazine has large holding capacity (up to 140 staples) I Quick release cam-lock opens guide assembly to easily clear jammed nails,
minimizing downtime I Depth adjustment drives staples to the precise level on the surface I Hook allows tool to remain close by ...
Makita AT2550A Reviews
We have not received any reviews for Makita yet.