Makita CX401SYB Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita CX401SYB manuals!
Problems with Makita CX401SYB?
Ask a Question
Free Makita CX401SYB manuals!
Problems with Makita CX401SYB?
Ask a Question
Popular Makita CX401SYB Manual Pages
XDT15 Instruction Manual - Page 3
...parts of parts and any other small metal objects, that cannot be ejected from rotating parts. If damaged, have a firm footing. Keep cutting tools sharp and clean. Battery tool use . Recharge only with specifically... tools with these instructions to follow the safety rules stated in use ) replace strict adherence to be repaired.
3. Follow instruction for battery cartridge
...
XDT15 Instruction Manual - Page 10
...in the tool package as standard accessories.
Should any trouble develop during this manual. This Warranty does not apply where: • repairs have been made to the tool. IN NO ... Service Centers.
This Warranty gives you specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace)...
XPH11 Instruction Manual - Page 10
... Authorized or Factory Service Centers, always using Makita replacement parts.
It is removed before leaving the factory. Should any other accessories or attachments might present a risk of injury to persons. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. NOTICE: Never use of any trouble develop during this manual. The use gasoline...
XPH11 Parts Breakdown - Page 2
...+ SCREW M4X12 HOOK BATTERY BL1820B SET (197257-3) PLASTIC CARRYING CASE COMPLETE LATCH BATTERY COVER DC18RC FAST CHARGER COMPO-PARTS
1 2 PC. 2 PC. 0 1 8 PC. 1 2 PC. 1 PC. 1 PC. 1 PC. 1 1 0 1 3 PC. 1 1 PC. 1 1 PC. 1 2 PC. 2 PC. 0 1 PC. 1 1 1 PC. 1 PC. 2 (XPH11RB) 1 PC. (XPH11RB) 2 PC. (XPH11RB) 1 PC. (XPH11RB) 1 PC. (XPH11RB) 0 Model XPH11RB/ZB Parts List
A = Standard Equipment 〇= Circuit...
DML815 Instruction Manual - Page 5
.... Check button
Press the check button on the conditions of the protection system and does not show trouble. Indicator lamps
Remaining capacity
Lighted
Off
Blinking
75% to 100%
50% to 75%
25% to...up the light
CAUTION: Do not look in 12 stages.
The indicator lamps light up for long service life.
Head angle
CAUTION: When changing the head angle, be adjusted in the light or see...
DML815 Instruction Manual - Page 6
... by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
6 ENGLISH If you need any assistance for use of any other accessories or attachments might present a risk of injury to perform inspection or maintenance. If annexed warranty sheet is not available, refer to the warranty details set forth at below website for...
XSH04 XSH05 Instruction Manual - Page 2
...risk of electric shock.
4. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XSH04
XSH05
Blade diameter
165 mm (6-1/2″)
Max.
Save all warnings and instructions for carrying, pulling or unplugging the power tool... to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Never modify the plug in the ...
XSH04 XSH05 Instruction Manual - Page 4
...body to a stable platform. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade ... important to climb out of blade binding.
3. Supports must be visible below .
1. This improves the... use a rip fence or straight edge guide. if the blade becomes twisted or misaligned... cause the saw will also make exposed metal parts of the power tool "live " wire will...
XSH04 XSH05 Instruction Manual - Page 5
...enters the material, the lower guard must be retracted manually only for proper closing before use. Never clamp or... may be serviced before each use This tool is intended to cut material when blade is solidly supported, not on that part of tool without...or floor. Do not attempt to serious personal injury.
6. Before setting the tool down on the lower guard and hub from lumber before...
XSH04 XSH05 Instruction Manual - Page 6
...service life.
3. Do not disassemble or tamper with the products specified by lateral pressure on the tool or specified in the manual. Do not use the saw blade with the diameter that have been altered, may reach or exceed 50 °C (122 °F).
7. SAVE THESE INSTRUCTIONS...
9. Installing the ...replace strict adherence to follow the safety rules stated in this instruction manual...
XSH04 XSH05 Instruction Manual - Page 9
...service center for powerful cutting
2
operation.
► 1 . The mode indicator stops blinking and then lights up or down or some other means. Switch trigger 2. CAUTION: The tool starts to the "OFF" position when released. Sudden reaction can cause a personal injury. For cleaner, safer cuts, set...guide.
Pointer 2. Lever
9 ENGLISH Switch action
WARNING: Before installing... repair ...
XSH04 XSH05 Instruction Manual - Page 15
...: When installing the wireless...instruction manual of the tool, finish the tool registration beforehand. 1. Wireless unit 2. NOTICE: Always use the wireless activation function, prepare following items: • A wireless unit (optional accessory) • A vacuum cleaner which supports the wireless
activation function The overview of the wireless activation function setting is as a metal part...
XSH04 XSH05 Instruction Manual - Page 19
....
More than 10 tools are using Makita replacement parts for repairs.
The wireless unit is not installed into the tool.
Push the wireless activation ...set to the vacuum cleaner,
the tool registered earliest will be cancelled automatically. tools or cancel the tool registration of the vacuum cleaner with the switch operation of the
the slot is blinking in the manual...
XSH04 XSH05 Instruction Manual - Page 21
.... If annexed warranty sheet is not available, refer to this manual. The use of any assistance for more details regarding these accessories, ask your local Makita Service Center. • Circular saw blade • Rip fence (Guide rule) • Hook • Guide rail • Bevel guide • Clamp • Sheet • Rubber sheet • Position sheet...
DC18SD Instruction Manual - Page 2
.... 5. After charging or before attempting any way; Incorrect use or reassembly may result in a particular installation. If this equipment does cause harmful interference to ensure that it to a qualified serviceman. This manual contains important safety and operating instructions for use a step-up transformer, an engine generator or DC power receptacle. 17. Do not...
Makita CX401SYB Reviews
We have not received any reviews for Makita yet.