Lantronix MSS4 Support and Manuals
Get Help and Manuals for this Lantronix item
View All Support Options Below
Free Lantronix MSS4 manuals!
Problems with Lantronix MSS4?
Ask a Question
Free Lantronix MSS4 manuals!
Problems with Lantronix MSS4?
Ask a Question
Most Recent Lantronix MSS4 Questions
Default Factory
como resetear a valores default factory un MSS4
como resetear a valores default factory un MSS4
(Posted by avelasquez63014 8 years ago)
Popular Lantronix MSS4 Manual Pages
MSS Quick Start Guide - Page 7
... you want to configure. 10
f ) Configure the port settings and click the Update Port Settings button at the bottom of settings. 6) To close the active sessions and implement the changes, power cycle
to reboot. WWW.LANTRONIX.COM
11 Quick Start Guide MSS100 / MSS-VIA / MSS4
CONFIGURE (CONT.) 4) Configure a group of settings:
a) Select a link from the left navigation column, for...
MSS User Guide - Page 9
...configure custom PC card support. The MSS supports TCP/IP protocols, including Telnet, Rlogin, UDP, DNS, and WINS.
‹ The Telnet terminal protocol, supported on what is a method of data in the Ethernet packets and provides different services for help system managers troubleshoot network and serial line problems.
‹ SDK Support The MSS supports the Lantronix Software Developer Kit (SDK...
MSS User Guide - Page 12
... chapter covers the installation of networking installation is pressed and held during the power up and boot procedure for at least 3 seconds, the MSS-VIA returns to its factory default configuration. MSS-VIA Installation
Components
The MSS-VIA front panel has a male DB9 RS-232 serial connector, a reset button, and a male DB25 serial connector supporting RS-232, RS...
MSS User Guide - Page 27
... includes assigning an IP address. d) For Loadhost, enter the IP address of up to six alphanumeric characters.
Specify a new password of the network host where you intend to use a mask other than the default. b) For IP Address, enter the desired IP address to store your MSS. Click OK. Note: If you have an older version of your operating code and SDK files...
MSS User Guide - Page 28
... replies from the first directed IP packet it sets its IP address is not necessary in Windows 95, the ARP table on which you're working. This has to be used or the MSS must have at the `Local_>' prompt for MSS-VIA and MSS4
% telnet 192.168.0.10
Trying192.168.0.10
Lantronix Version n.n/n (yymmdd) Type Help at...
MSS User Guide - Page 29
... will not reply to use the Change Server DHCP Enabled command. MSS User Guide
3: Getting Started
Figure 3-7: Changing the IP Address for MSS100
% telnet 192.168.0.10
Trying 192.168.0.10
Lantronix Version n.n/n (yymmdd) Type Help at the Local Prompt for MSS100
Local> SET PRIVILEGED Password> system (not echoed) Local>> CHANGE IPADDRESS 192.168.0.10
3-18
Become...
MSS User Guide - Page 30
... should be configured to six alphabetic characters. This behavior can be changed as soon as possible.
Simply type the MSS IP address or resolvable Hostname into it is access. The incoming password feature can be disabled with the Change Server Incoming Password command.
MSS User Guide
3: Getting Started
Incoming Logins
Incoming Telnet logins are enabled by default.
MSS User Guide - Page 32
....168.0.16 Trying 192.168.0.16 Connected to MSS100 models only.
Connections to the remote console port, use the Telnet command followed by the MSS IP address and the remote console port number. Figure 3-17: LAT Login
$ SET HOST/LAT MSS_xxxxxx
Changing the Login Password
The login password is enabled. To connect to the console port cannot...
MSS User Guide - Page 35
...
Local>> CHANGE IPADDRESS 192.168.0.10
Subnet Mask IP networks can be configured automatically. IP Address The IP address can be divided into subnetworks, you want to remove all custom configuration from the MSS, including password settings. When a network is subnetted, some of the host part of each address is part of the address. If your network is restored. You must agree...
MSS User Guide - Page 60
... to diagnose network transmission problems.
Show Sessions
This command displays information about send and receive errors. Software and ROM versions, configured loadhosts, and startup files are shown. In addition, inactivity and retransmission limits, password restrictions, and the types of addresses are listed according to the MSS-VIA only.
5-5 Addresses or ranges of incoming...
MSS User Guide - Page 76
... MSS software resides on this firmware. Always download and read the RELEASE.TXT file for the filename. ‹ Use the List Server Boot command to check settings before using the Initialize Reload command to update Flash ROM, the following points are reloading the correct software file. The contents of Flash ROM can be updated by FTP (ftp.lantronix...
MSS User Guide - Page 77
...>> LIST SERVER BOOT Local>> INITIALIZE RELOAD
Note: For instructions on how to log into the MSS to Troubleshooting Flash ROM Updates.
Enter the privileged user password (the default is the correct directory.
6. the default login directory is system).
4.
Some BOOTP and TFTP implementations require a specific directory for software reload, use the following commands. If the download...
MSS Reference Manual - Page 22
...page 2-12; Errors
Autostart and Autobaud are discarded.
Port numbers are specified with integers between 1 and 4, and should be idle unless DSR is held low, and therefore will affect the MSS4's current port ...Command Reference
Note:
Defaults See Also
In the absence of the Portlist parameter, the configuration will wait for a carriage return or pre-set for ranges).
Change ...
MSS Reference Manual - Page 37
... ports.
2-27 Parameters
Server MSS4 only. Errors
You will take effect immediately.
The Ports parameter, applicable only to the MSS4, restricts connections to the given IP address from certain ports, and connections from this address to enter the login password when attempting an incoming connection. the Getting Started chapter of your Installation Guide.
2.25 Change IPSecurity...
MSS Reference Manual - Page 76
... about the serial port's current session(s).
Errors
Does not apply to see .
All services will not be shown if no service is specified. Characteristics Displays server settings including hardware address, timer limit, password limit, session limit, retransmit limit, IP address, subnet mask, nameserver, gateway, and more.
For the MSS4, this command shows the current session...
Lantronix MSS4 Reviews
We have not received any reviews for Lantronix yet.