KitchenAid KMMF330PSS Support and Manuals
Get Help and Manuals for this KitchenAid item
This item is in your list!
View All Support Options Below
Free KitchenAid KMMF330PSS manuals!
Problems with KitchenAid KMMF330PSS?
Ask a Question
Free KitchenAid KMMF330PSS manuals!
Problems with KitchenAid KMMF330PSS?
Ask a Question
Popular KitchenAid KMMF330PSS Manual Pages
Owners Manual - Page 2
... messages. This is in the manual.
parts made at home using the appliance.
� Read and follow instructions. We have not been recommended by the manufacturer (e.g. Grease should be serviced only by children.
� Do not operate this appliance if it has a damaged cord or plug, if it is specifically designed to properly grounded outlet...
Owners Manual - Page 3
...repaired by anyone except properly qualified service personnel.
3
Do not leave paper products, cooking utensils, or food in the cavity when not in harmful exposure to microwave energy. SAVE THESE INSTRUCTIONS...important that the oven door close properly and that there is damaged. IMPORTANT SAFETY INSTRUCTIONS
� Use care when cleaning the vent-hood filter. Corrosive cleaning agents,...
Owners Manual - Page 4
... washcloths, or some models)
To avoid damage to stainless steel surfaces, do not use .
Steam will soften soil.
See the "Venting Design Specifications" section.
†Affresh...Quick Start Guide to 5 minutes in direction of Whirlpool, U.S.A. 4
GREASE FILTERS
� Mild cleanser and scouring pad � Dishwasher
INSTALLATION INSTRUCTIONS
REQUIREMENTS
Tools and Parts
Tools Needed...
Owners Manual - Page 6
...
C. Location Requirements
Check the opening . � Support for cooking. The location must be inside the upper cabinet. Check with door) 12" (30.5 cm) to Round Transition" illustration in the "Venting Design Specifications" section.
Product Dimensions
B
A C
A. 297/8" (76.1 cm) B. 177/8" (45.4 cm) C. 121/8" (31.3 cm)
Installation Dimensions
NOTE: The grounded 3 prong outlet must...
Owners Manual - Page 8
Recirculation (Factory Default Setting)
Wall Venting
Roof Venting
Find the Cardboard Plate
.... Cabinet opening vertical centerline
C. Wall stud centerlines
D. A. Holes for lag screws E. Support tabs F.
See illustrations in the carton.
Holes for lag screws E. Support tabs F.
Find it before installation. Mounting plate center
markers
C
D
C
D
A
A
A
E
E
E
F
...
Owners Manual - Page 9
...block the air outlet. Grille baffle
B
B
A. End holes (on mounting plate)
B. Holes for lag screws E. Cabinet door B. Support tabs F. Flush to Cabinet door A B
C
Flush to flush the cabinet, and the flush point before installation. Cabinet door B. Microwave oven
door
A. Holes for lag screws E. Cabinet door B. Cabinet C. Cabinet B. Wall stud centerlines
A,D
E C
D. Microwave...
Owners Manual - Page 10
..., you can be flush with the vertical wall centerline. Place the cardboard plate against the bottom of 12" to be adjusted outward to 13" cabinet installation, but need some adjustment for depth of the upper
cabinet.
NOTES:
� Make sure the front edge
of the cardboard plate
B
align with the upper...
Owners Manual - Page 12
...with the A & B & H & J holes marked in the cavity, take it to 180 degree at mounting plate to be installed around the supply cord hole as shown. B
D
C
B
E
A
A. A & B & H & J holes C. ...Mark E. Drill two mounting nut holes (B), which are for recirculation venting or wall
venting installation. B
2. Roof Venting Cutout Area
Drill holes in Upper Cabinet
1. Bottom Edge of...
Owners Manual - Page 13
... at both end holes. 4. Mounting Plate B. With the support tabs of the mounting plate facing forward, insert 3/16-24... A & B hole, do not drill A & B hole, and follow the below instruction. Start toggle nuts on at least 1 wall stud, the mounting plate must be secured...Wall Stud Configurations" in Step 3 of the mounting plate. If installing on at least 1 wall stud as well as at Both ...
Owners Manual - Page 14
...support tabs of the mounting plate facing forward, insert a 3/16-24 x 3" round-head bolt through the end hole that fits over the 5/8" (16 mm) hole drilled in step 3 of "Installation... follow the propriated instruction to back of the mounting plate. If installing on a second...Installation for the toggle nut to go through the drywall, and finger
tighten the bolt to the microwave oven, and set...
Owners Manual - Page 16
...covers on the damper plate at the perforations. Return the damper plate to 5 from "Wall Venting Installation Only."
16 Damper plate 8. A
B
A. Damper plate B.
Reconnect the blower motor wire into microwave... microwave oven. Repeat Steps 1 to its original horizontal position. Check to follow these instructions can result in the blower motor screw holes, so that the motor cannot move....
Owners Manual - Page 17
... B. Check that the long tab of mounting plate. Insert damper assembly through the cabinet cutout so that damper blade moves freely and opens fully.
2.
Support tabs
17
Mounting plate B. A
B
A. Upper cabinet cutout E. Damper plate
3. Install Damper Assembly for recirculation installation, no need to do not grip or use . Damper blade D. #6 x 3/8" Sheet metal screws...
Owners Manual - Page 18
...cabinet. Using 2 or more people, lift microwave oven off of mounting plate, and set aside on the cavity and programming a cook time of water on a covered surface...Instructions for troubleshooting information. The blocks must be added. Mounting Nut
Complete Installation
1. Replace the fuse or reset the circuit breaker. Bolts
A. Reconnect power. 5. Check the operation of /recycle all parts...
Owners Manual - Page 19
Save Installation Instructions for installation are not provided with
microwave hood combination. � We do not recommend using recirculation installation. Wall or back of... of the vent
and number of the cabinet D. 0.5"-0.75" (1.3-1.9 cm)
VENTING DESIGN SPECIFICATIONS
Venting Design Specifications
This section is intended for the damper to vent air outside,
unless using a flexible ...
Owners Manual - Page 20
... system. Rectangular-to-Round Transition
NOTE: The minimum 3" (76 mm) clearance must exist between the damper assembly and rectangular to round transition piece must be installed to keep the damper from sticking.
20 Two 90° elbows = 20 ft (6.1 m) B. 1 wall cap = 40 ft (12.2 m) C. 1 rectangular-to-round transition piece = 5 ft (1.5 m) D. 2 ft...
KitchenAid KMMF330PSS Reviews
Do you have an experience with the KitchenAid KMMF330PSS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for KitchenAid yet.
Earn 750 points for your review!