KitchenAid KMHS120KPS Support and Manuals
Get Help and Manuals for this KitchenAid item
View All Support Options Below
Free KitchenAid KMHS120KPS manuals!
Problems with KitchenAid KMHS120KPS?
Ask a Question
Free KitchenAid KMHS120KPS manuals!
Problems with KitchenAid KMHS120KPS?
Ask a Question
Popular KitchenAid KMHS120KPS Manual Pages
Quick Reference Sheet - Page 1
... container and cover with plastic wrap. Rest on paper towel. Senses 1-4 cups (250 mL-1 L): Place in microwave-safe container. KitchenAid® Microwave Hood Combination Model YKMHS120 Quick Reference Guide
POPCORN (sensor)
Senses 3.0-3.5 oz (85-99 g) size bag: Place bag on plate, cover with plastic wrap, and vent. Senses 1-4 cups (250 mL-1 L): Remove...
Quick Reference Sheet - Page 2
... quantities of container. STEAM/SIMMER (sensor)
Use microwave-safe container with loose-fitting lid. Senses 0.5-1.5 lbs (142-680 g):
2 Manual Steam: Place small microwave-safe dish (for example, custard dish) with loose-fitting lid.
3 Manual Simmer
Rice: Add liquid and food to boil, then begin counting down after the sensor detects steam from...
Installation Instructions - Page 2
... on model, aluminum grease filter and charcoal filter may not be combined. See the "Venting Design Specifications" section.
2 NOTE: The hardware items listed here are for wall or roof venting. See User Instructions.)
NOTE: Depending on reordering, see the "Replacement Parts" section. Materials Needed
Standard fittings for wood studs. MICROWAVE HOOD COMBINATION SAFETY
INSTALLATION...
Installation Instructions - Page 3
...■ Some models have a pocket handle. Set the cardboard template ...Cabinet" parts of installation.
12 1/2" (31,8 cm) 6 1/4" (15,9 cm)
5 3/4" (14,6 cm)
Installation Dimensions...cabinet template is embedded in the "Venting Design Specifications" section. Cut along the dotted line to...Support for 66" (167.6 cm) installation height. For Roof Venting Installation Only:
■ If you can be...
Installation Instructions - Page 4
...; A time-delay fuse or time-delay circuit breaker ■ A separate circuit serving only this microwave oven
GROUNDING INSTRUCTIONS
For all governing codes and ordinances. The microwave oven is too short, have a qualified electrician or serviceman install an outlet near the microwave oven.
Do not use of the grounding plug can result in a risk...
Installation Instructions - Page 5
..., do not grip or use the door or door handle while the microwave oven is set the screws aside. Rotate Blower Motor
The microwave oven is being handled. A
A.
Damper plate
A. INSTALLATION INSTRUCTIONS
Remove Mounting Plate
Depending on your model, the mounting plate may be in another location where wall or roof venting may be...
Installation Instructions - Page 7
... its original horizontal position. Damper plate 12. Secure damper plate with two screws removed in Step 1. Diagonal wire cutting pliers 7. A
B
A. Repeat Step 1 from "Wall Venting Installation Only." 4. A
B
A.
A
8.
A
A. Exhaust ports face the top of the microwave oven (as shown), performance will be poor.
7 Exhaust port
IMPORTANT: If blower motor is not positioned...
Installation Instructions - Page 8
... C.
Holes for lag screws E. Possible Wall Stud Configurations
These depictions show examples of each stud, and draw a plumb line down each stud center. Support tabs F.
Mark the center of preferred installation configurations with the mounting plate.
End holes (on mounting plate) B. Mounting plate center markers
8 See illustrations in "Possible Wall Stud Configurations."
Installation Instructions - Page 9
...venting cutout area.
Top of the upper cabinet. With the support tabs facing forward (see illustrations in the "Locate Wall ...back
edge, lower the cardboard template so that the end holes are ideal hole locations.
7. Set the mounting plate aside. Centerline
2. D A
C
B
Upper cabinet bottom
4" (10.2... Mark Rear Wall
The microwave oven must be installed on a level line with each be 141&#...
Installation Instructions - Page 10
...installation configurations. Installation for No Wall Studs at End Holes (Figures 1 and 2)
1. No Wall Studs at End Holes (Figures 1 and 2)
NOTE: The mounting plate must attach to Figure 3 in "Possible Wall Stud Configurations" in the "Locate all lag screws and bolts. With the support... toggle nuts on bolts from the back of "Installation for the toggle nuts to go through the drywall...
Installation Instructions - Page 11
...thickest part of the rear wall (for the power supply cord. Make sure the 10" (25.4 cm) dimension from the rear wall to be installed around the supply cord hole as installed) has... and "E" on the template. Drill 3/8" (1 cm) holes at the circular shaded area "G" on the template. Install Damper Assembly
(for two 1/4-20 x 3" bolts and washers used to secure the microwave oven to outlet. 2. ...
Installation Instructions - Page 12
..., and set aside on your model, it ...may be adjusted, skip steps 7 through the wall, make sure the damper assembly fits easily into microwave oven.
Place a washer on support tabs at most hardware stores.
■ Overtightening bolts may require bolts longer or shorter than 3" (7.6 cm). Adjust mounting plate and retighten screws. 10. A
B A. Support tabs
12
A. Install...
Installation Instructions - Page 13
... 3/8" sheet metal screw. Install filters. Refer to the mounting nut, screw the bolts into a grounded 3 prong outlet.
■ See the User Instructions for troubleshooting information. Bolt B. Then ...problem continues, call an electrician.
■ Check that the long tab of the damper assembly slides under vent)
13 Save Installation Instructions for future use.
2. Long tab F. The installation...
Installation Instructions - Page 14
... damper to open freely and fully. A
B
C
D
E
3" (7.6 cm)
F
A. Elbow (for installation are not provided with microwave hood combination.
■ We do not recommend using a flexible metal vent.
&#...of clearance between the top of the microwave oven and the transition piece.
VENTING DESIGN SPECIFICATIONS
This section is used, be sure there are at least 3" (7.6 cm) high
...
Installation Instructions - Page 15
... 8171338 Biscuit 8171339 Stainless Steel
99403 Almond
See your authorized dealer or service center.
Both numbers can be replaced, call us at our toll-free number or visit our website listed...Guide. Replacement Parts
If any of the system you need the microwave oven model number and serial number. To calculate the length of the installation hardware needs to be found on the model...
KitchenAid KMHS120KPS Reviews
We have not received any reviews for KitchenAid yet.