Kenwood NX-820 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-820 manuals!
Problems with Kenwood NX-820?
Ask a Question
Free Kenwood NX-820 manuals!
Problems with Kenwood NX-820?
Ask a Question
Popular Kenwood NX-820 Manual Pages
Operation Manual - Page 3
VHF DIGITAL TRANSCEIVER
NX-720 NX-720G
UHF DIGITAL TRANSCEIVER
NX-820 NX-820G
INSTRUCTION MANUAL
NOTIFICATION This equipment complies with the essential requirements of Directive 2014/53/EU. AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166 This equipment requires a licence and is intended for use in the countries as below.
Operation Manual - Page 5
...9670; Illegal operation is mounted in gasoline service stations. Do not transmit while the caps...sure they may cause them to explode. This instruction manual covers only the basic operations of unlicensed transmitters within...
We are grateful you have chosen KENWOOD for countries that the operator is aware... and the environment. NOTICES TO THE USER
◆ Government law prohibits the operation...
Operation Manual - Page 7
... set • 5 x 16 mm self-tapping screw 4 • M4 x 6 mm hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual ...for use a circle cutter to drill a hole, then install a rubber grommet.
2 Run the power cable through ... your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. GETTING STARTED
Note: The following instructions are ...
Operation Manual - Page 16
... Press the / key to select the station you want to call by JVC KENWOOD Corporation. Each transceiver has its own ID. • Enter a Fleet number ...and speaking into the microphone.
■ Identification Codes An ID code is a combination of a 3-digit Fleet number and a...is enabled, you want to call. • If Manual Dialing is a voice call ). Note: This function is entered. 4...
Operation Manual - Page 17
If set up by your transceiver. SHORT MESSAGES
This transceiver can receive short data messages which contain a maximum of 48 characters... # key.
5 Press the / key to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a station ID by using the NX-720/ NX-820, you must connect an external GPS unit. • When the power is turned ON and/or the ...
Operation Manual - Page 19
...
A calling ID or text message will appear when a Status call is received. Press any key to return to enter Manual Input mode. Press the / key to select the digit you can enter the Code directly by using the microphone DTMF keypad.
6 Press the key programmed as [Call 1] to [Call 6] to change the...
Operation Manual - Page 20
... and hold the A or # key to delete all digits. 10 Repeat steps 8 and 9 to enter the entire number.
14 DTMF (DUAL TONE MULTI FREQUENCY) CALLS
MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired digits using the microphone DTMF keypad.
• If you release the PTT switch, transmit mode...
Operation Manual - Page 22
...DQT code is set the transceiver to ignore (not hear) calls from other parties who are 16 available Scrambler codes or... Encryption keys (1 ~ 16). Operator Selectable Tone (OST) If a key has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the key programmed as [Emergency].
• Ask your dealer for further information. Contact your KENWOOD...
Operation Manual - Page 171
VHF
NX-720 NX-720G
UHF
NX-820 NX-820G
2014/53/EU
AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166
Operation Manual - Page 185
4 S 5
DTMF 3 6 PTT COMPLETE
1 Selcall Selcall Stack 2 ID S S 1 3 A S A 1 S ή .
48
15
GPS
GPS GPS GPS NX-720G/ NX-820G GPS KRA-40 NX-720/ NX-820 GPS GPS είναι
G-11
Operation Manual - Page 196
... types NX-720-E, NX-720G-E, NX-820-E, NX-820G-E are described in the EU declaration of conformity is available at the following internet address: http://www.kenwood.com/cs/com/ecdoc/ (Note: The detail type designations are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity.)
Model NX-720-E NX-720G-E NX-820-E NX-820G...
Operation Manual 1 - Page 1
NX-720 NX-820
VHF DIGITAL TRANSCEIVER UHF DIGITAL TRANSCEIVER
INSTRUCTION MANUAL
B62-2448-10 (C)
Operation Manual 1 - Page 3
... voice coding Technology is protected by fine and/or imprisonment. ◆ Refer service to explode. This instruction manual covers only the basic operations of your radio. Firmware Copyrights The...a padded interior.
The user of this Technology is aware of, and understands, hazards common to the operation of copyrights for firmware embedded in KENWOOD product memories are reserved ...
Operation Manual 1 - Page 5
...washer 4 • Flat washer 4 Instruction manual 1
PREPARATION
Various electronic equipment in your...set • 5 x 16 mm self-tapping screw 4 • M4 x 6 mm hex-headed screw with the carrier immediately. SUPPLIED ACCESSORIES
Carefully unpack the transceiver. If your KENWOOD dealer, an authorized KENWOOD service...circle cutter to drill a hole, then install a rubber grommet.
2 Run the ...
Operation Manual 1 - Page 15
...message is received. 5 Press the / key to select the status you want to transmit. • If Manual Dialing is enabled, you must first connect a GPS unit to the transceiver. A maximum of your ...be automatically transmitted at a preset time interval.
11 GPS REPORT
To send your transceiver. If set up by pressing the key programmed as Status messages. Press any key to return to normal ...
Kenwood NX-820 Reviews
Do you have an experience with the Kenwood NX-820 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!