Kenwood NX-348 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-348 manuals!
Problems with Kenwood NX-348?
Ask a Question
Free Kenwood NX-348 manuals!
Problems with Kenwood NX-348?
Ask a Question
Popular Kenwood NX-348 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-248
UHF DIGITAL TRANSCEIVER
NX-348
© B5A-0068-10 (C)
Operation Manual - Page 3
...by fine and/or imprisonment. ◆ Refer service to the operation of Digital Voice Systems, Inc. This voice coding Technology is punishable by intellectual property rights including patent rights...any transceiver.
U.S. Firmware Copyrights The title to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in KENWOOD product memories are grateful you have ...
Operation Manual - Page 4
...instructions
and regulations provided by the airline crew.) • Where restrictions or warnings are posted regarding the use options not specified by KENWOOD. • If the die-cast chassis or other transceiver part is damaged, do
not touch the damaged parts... squelch off before installing optional accessories. ...Do not touch these locations when replacing the battery pack. • Do...
Operation Manual - Page 5
... the transceiver, ensure that the strap is possible for any metallic parts are exposed from the transceiver, and contact your country or region.... ear. you are driving may be ejected and strike the driver or passengers. • Do not transmit while touching the ..., it is durable. When using an earphone accessory in your KENWOOD dealer. • Use of batteries, be against traffi...
Operation Manual - Page 9
...
• Antenna (Supplied with the carrier immediately. If any of the items listed below are missing or damaged, file a claim with NX-348 1 • Cap 1 • Locking bracket 1 • Belt clip (KBH-10 1 • Screw (M3 x 8 mm 2 • Channel stopper 1 • Instruction manual 1 Note: ◆ Refer to "PREPARATION" {p. 2} for accessory installation instructions.
1
Operation Manual - Page 10
... not exist. • Selecting a channel which does not exist causes a continuous error
tone to sound. 1 Set the Channel selector to change. 2 Insert the channel stopper. 3 Set the arrow of the transceiver by holding the antenna at channel 1, the knob may
not install correctly and the channel may damage the antenna and degrade your transceiver...
Operation Manual - Page 17
... Select If the scan priority type is a safety feature built into the transceiver. On high transmit power channels, press this key in normal mode to set the current channel as Key Lock except that when the transceiver power is turned OFF and then ON again, the keys remains locked.
■ Lone...
Operation Manual - Page 19
... decreases it .
11 Enter the password (up to 4 digits) using the following procedure. 1 Set the Channel selector to position "1". 2 Press the Side 1 or Side 2 key to confirm the password. • When the correct password is password protected, the LED will light blue when you enter an incorrect password, an error tone sounds and the transceiver...
Operation Manual - Page 20
... it becomes free. 3 Press the PTT switch and speak into the microphone. This
will hear a call only if the received signal matches your transceiver settings. Refer to code your mouth.
If signaling has been programmed on the selected channel, you will prevent you from your calls. TRANSMITTING
1 Select the desired zone and...
Operation Manual - Page 21
... operation. VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you are using a supported headset. To activate VOX and set the LED to blink either orange or blue for specific channels by your dealer. VOX ...can set the VOX Gain level, perform the following steps:
1 Connect a headset to the ...
Operation Manual - Page 22
... the sector points to empty channel, pressing Side 2 key will cause the error tone to sound.
5 Press the PTT switch to save the setting. • A beep will sound. • The transceiver announces the new...transceiver to key in the correct password before entering the VOX setup mode.
Note: ◆ If key lock with the Channel selector). 4 Press the Side 1 key to set , the user need to start ...
Operation Manual - Page 23
...seconds). To make a call , press the key programmed as [Call 1] or [Call 2], if they have set the duration for the auto reset timer (default is a general term for Individual or
Group calls, allowing you ... caller's voice. When you receive a group call . • Your dealer may also have been set up with an NXDN Status. • Channels are possible.
After the tone ends, you to start...
Operation Manual - Page 24
....
Note: ◆ While the Battery Saver is released and the LED indicator blinks red when the battery needs recharged or replaced. BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The Time-out Timer prevents callers from interfering on how BCL functions when
using a...flash green
when receiving a QT/DQT signal which does not match the QT/ DQT tone/code set up in use.
To stop the tone.
Operation Manual - Page 25
...is an optional signaling system available only for digital communications.
■ DTMF A DTMF PTT ID is set up with ID, and "Wild Card" Group Calling.
17
When a channel is included for digital ...radio communications. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is received.
If a call . Note: ◆ PTT...
Kenwood NX-348 Reviews
Do you have an experience with the Kenwood NX-348 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!