Instruction Manual
Page 2
..., batteries, and accumulators (rechargeable batteries) must be taken to this instruction manual. DO NOT use of any Icom or non-Icom equipment, if the malfunction is not manufactured or approved by Icom. DO NOT connect the transceiver to operate the transceiver. IMPORTANT READ THIS ...far away as a 24 volt battery. This will increase several fold due to an AC outlet. RWARNING! NEVER install the IC-M700PRO into a positivegrounding ship. Icom is not usable. EXPLICIT DEFINITIONS The explicit definitions described below -20°C (-4°F) or above +60°C (+140...
..., batteries, and accumulators (rechargeable batteries) must be taken to this instruction manual. DO NOT use of any Icom or non-Icom equipment, if the malfunction is not manufactured or approved by Icom. DO NOT connect the transceiver to operate the transceiver. IMPORTANT READ THIS ...far away as a 24 volt battery. This will increase several fold due to an AC outlet. RWARNING! NEVER install the IC-M700PRO into a positivegrounding ship. Icom is not usable. EXPLICIT DEFINITIONS The explicit definitions described below -20°C (-4°F) or above +60°C (+140...
Instruction Manual
Page 13
...shift frequency and FSK polarity can be adjusted in the set mode (p. 12). ➥ Some transceivers may operate 1.7 kHz higher than the IC-M700PRO's J2B mode, even when the same displayed frequencies are available, depending on page 12. ➥ Full break-in (receiving is possible while ...➥ CW mode is not available in some versions. ➥ CW narrow can be selected in (automatic transmission with keying) ➥ OFF (manual transmission is installed. (p. 12) CW key connection 425 1 3 687 pin 2 pin 1 ACC(1) socket CW key ■ FSK operation The transceiver ...
...shift frequency and FSK polarity can be adjusted in the set mode (p. 12). ➥ Some transceivers may operate 1.7 kHz higher than the IC-M700PRO's J2B mode, even when the same displayed frequencies are available, depending on page 12. ➥ Full break-in (receiving is possible while ...➥ CW mode is not available in some versions. ➥ CW narrow can be selected in (automatic transmission with keying) ➥ OFF (manual transmission is installed. (p. 12) CW key connection 425 1 3 687 pin 2 pin 1 ACC(1) socket CW key ■ FSK operation The transceiver ...
Instruction Manual
Page 14
...available on a new frequency. Tuning starts only when [TUNE] is pushed. (default) Channel scan Scan is required, this section are using a non-Icom tuner (p. 19). (2) Automatic tuning operation When the optional AT-130 automatic antenna tuner is connected, tuning can be started automatically without the [TUNE] switch... AT-120 AH-3 Tuning starts when pushing [PTT] on some transceiver versions. q If necessary, push [POWER] to turn power OFF. If manual tuning is canceled when transmitting. e Rotate the [GROUP] selector to function as "channel scan" or "channel resume scan."
...available on a new frequency. Tuning starts only when [TUNE] is pushed. (default) Channel scan Scan is required, this section are using a non-Icom tuner (p. 19). (2) Automatic tuning operation When the optional AT-130 automatic antenna tuner is connected, tuning can be started automatically without the [TUNE] switch... AT-120 AH-3 Tuning starts when pushing [PTT] on some transceiver versions. q If necessary, push [POWER] to turn power OFF. If manual tuning is canceled when transmitting. e Rotate the [GROUP] selector to function as "channel scan" or "channel resume scan."
Instruction Manual
Page 15
... Automatic keying without the optional filter installed, the transceiver does not function in allows you to mute receiving until keying stops with delay time OFF Manual transmission necessary for keying 12 This item allows you to select one of these modes. (6) FSK frequency shift Several shift settings (the difference between transmitted...
... Automatic keying without the optional filter installed, the transceiver does not function in allows you to mute receiving until keying stops with delay time OFF Manual transmission necessary for keying 12 This item allows you to select one of these modes. (6) FSK frequency shift Several shift settings (the difference between transmitted...
Instruction Manual
Page 25
... microphone too close to your mouth. or distorted. ÷ Microphone is not properly matched to the ÷ Push [TUNE] to an Icom Service Center. Check the following chart before making any adjustments or sending the transceiver to tune the using antenna pgs. p. 2 ÷ ...(or p. 3 transmission. POWER RECEIVE PROBLEM POSSIBLE CAUSE SOLUTION REF. No sound comes from the ÷ The [SPEAKER] switch is selected. when manual tuning is turned OFF. Transmit signal is unclear ÷ The wrong operation mode is closed. ÷ Turn ON the [SPEAKER] switch. only ...
... microphone too close to your mouth. or distorted. ÷ Microphone is not properly matched to the ÷ Push [TUNE] to an Icom Service Center. Check the following chart before making any adjustments or sending the transceiver to tune the using antenna pgs. p. 2 ÷ ...(or p. 3 transmission. POWER RECEIVE PROBLEM POSSIBLE CAUSE SOLUTION REF. No sound comes from the ÷ The [SPEAKER] switch is selected. when manual tuning is turned OFF. Transmit signal is unclear ÷ The wrong operation mode is closed. ÷ Turn ON the [SPEAKER] switch. only ...