Instruction Manual
Page 20
... TERMINAL [GND] (p. 15) Connect this terminal to a station or vehicle ground to prevent electrical shocks, TVI, BCI and other problems. !1 ANTENNA CONNECTOR [ANT1], [ANT2] (p. 17) Accepts a 50 Ω antenna with another Icom CI-V transceiver or receiver. for packet operation. • See page at right for connection to an 144/430 MHz antenna...
... TERMINAL [GND] (p. 15) Connect this terminal to a station or vehicle ground to prevent electrical shocks, TVI, BCI and other problems. !1 ANTENNA CONNECTOR [ANT1], [ANT2] (p. 17) Accepts a 50 Ω antenna with another Icom CI-V transceiver or receiver. for packet operation. • See page at right for connection to an 144/430 MHz antenna...
Instruction Manual
Page 24
...15 For a description and a diagram of two angles depending on your transceiver from TV sets, TV antenna elements, radios and other problems, ground the transceiver through the GROUND terminal on the rear panel. Use wellmatched 50-ohm antennas and coaxial feedline. Strip the cable...in 1-2 mm 1⁄16 in) ANTENNA SWR Each antenna is tuned for output power and sensitivity. The IC-7000 has an SWR meter to one of accessory equipment included with the IC-7000, see description on right hand page) ■ Grounding To prevent electrical shock, television interference (TVI), ...
...15 For a description and a diagram of two angles depending on your transceiver from TV sets, TV antenna elements, radios and other problems, ground the transceiver through the GROUND terminal on the rear panel. Use wellmatched 50-ohm antennas and coaxial feedline. Strip the cable...in 1-2 mm 1⁄16 in) ANTENNA SWR Each antenna is tuned for output power and sensitivity. The IC-7000 has an SWR meter to one of accessory equipment included with the IC-7000, see description on right hand page) ■ Grounding To prevent electrical shock, television interference (TVI), ...
Instruction Manual
Page 26
Grounding prevents electrical shocks, TVI and other problems. KEY ACC DATA MIC GND ANT2 ANT1 DC 13.8V 2 m/70 cm ANTENNA DC POWER SUPPLY (p.19) PS-126 HF/50 MHz ANTENNA 17 2 INSTALLATION AND CONNECTIONS ■ Required connections MICROPHONE (p. 10) STRAIGHT KEY HM-151 RTTY TERMINAL UNIT (p. 23) GROUND (p. 15) Use the heaviest gauge wire or strap available and make the connection as short as possible.
Grounding prevents electrical shocks, TVI and other problems. KEY ACC DATA MIC GND ANT2 ANT1 DC 13.8V 2 m/70 cm ANTENNA DC POWER SUPPLY (p.19) PS-126 HF/50 MHz ANTENNA 17 2 INSTALLATION AND CONNECTIONS ■ Required connections MICROPHONE (p. 10) STRAIGHT KEY HM-151 RTTY TERMINAL UNIT (p. 23) GROUND (p. 15) Use the heaviest gauge wire or strap available and make the connection as short as possible.
Instruction Manual
Page 146
... this may damage the transceiver's surfaces. 137 R WARNING! Screw driver DC power cable fuse replacement Fuse cover ■ Memory backup All of the problem, repair it clean with a new, adequately rated fuse. All data you set mode contents, etc. These may result in the FRONT unit. ... battery. ■ Cleaning If the transceiver becomes dusty or dirty, wipe it , and replace the damaged fuse with a dry, soft cloth. The IC-7000 has three fuses (DC power cable fuses × 2, circuitry fuse × 1) installed for the power amplifier, through the circuitry fuse. There is...
... this may damage the transceiver's surfaces. 137 R WARNING! Screw driver DC power cable fuse replacement Fuse cover ■ Memory backup All of the problem, repair it clean with a new, adequately rated fuse. All data you set mode contents, etc. These may result in the FRONT unit. ... battery. ■ Cleaning If the transceiver becomes dusty or dirty, wipe it , and replace the damaged fuse with a dry, soft cloth. The IC-7000 has three fuses (DC power cable fuses × 2, circuitry fuse × 1) installed for the power amplifier, through the circuitry fuse. There is...
Instruction Manual
Page 147
... installed in the DC power cable and the other is set too low. check the SEND line of this chart, contact your nearest Icom Dealer or Service Center. phone plug connection. Reconnect to clear the PBT function. The antenna is improperly connected. Push [P.AMP/ATT] to...1, open the squelch. 25, 35 The transceiver is not connected properly. Receive distorted signals. Preamp is designed to locate the cause of a problem or solve it through the use of an external unit, if connected. 15 TROUBLESHOOTING The following chart is activated. improper conditions. Push [P.AMP...
... installed in the DC power cable and the other is set too low. check the SEND line of this chart, contact your nearest Icom Dealer or Service Center. phone plug connection. Reconnect to clear the PBT function. The antenna is improperly connected. Push [P.AMP/ATT] to...1, open the squelch. 25, 35 The transceiver is not connected properly. Receive distorted signals. Preamp is designed to locate the cause of a problem or solve it through the use of an external unit, if connected. 15 TROUBLESHOOTING The following chart is activated. improper conditions. Push [P.AMP...
Instruction Manual
Page 148
... impossible. Reset the CPU. Memory select scan 2 or more memory channels have been programmed in the M-3 menu to turn the function OFF. 15 TROUBLESHOOTING TRANSMIT PROBLEM Transmitting is set too high with other stations. Power is cut or shorted. Displayed frequency does not change properly. p. 38 Set compression level to a lower...
... impossible. Reset the CPU. Memory select scan 2 or more memory channels have been programmed in the M-3 menu to turn the function OFF. 15 TROUBLESHOOTING TRANSMIT PROBLEM Transmitting is set too high with other stations. Power is cut or shorted. Displayed frequency does not change properly. p. 38 Set compression level to a lower...
Service Manual
Page 2
...LCD LTA025A161A IC-7000 8810009610 Screw FH M2.6 × 6 ZK IC-7000 Front unit 5 pieces Top cover10 pieces Addresses are subject to 60 dB attenuator between the transceiver and a deviation meter or spectrum analyzer when using such test equipment. 8. Make sure the problem is internal...transceiver's front end. ALWAYS connect a 50 dB to change without notice or obligation. READ the instructions of the variable components. Icom, Icom Inc. DO NOT force any of test equipment thoroughly before disassembling the transceiver. 2. DO NOT keep power ON for your convenience....
...LCD LTA025A161A IC-7000 8810009610 Screw FH M2.6 × 6 ZK IC-7000 Front unit 5 pieces Top cover10 pieces Addresses are subject to 60 dB attenuator between the transceiver and a deviation meter or spectrum analyzer when using such test equipment. 8. Make sure the problem is internal...transceiver's front end. ALWAYS connect a 50 dB to change without notice or obligation. READ the instructions of the variable components. Icom, Icom Inc. DO NOT force any of test equipment thoroughly before disassembling the transceiver. 2. DO NOT keep power ON for your convenience....