Parts Manual
Page 9
... 68 06-00 376 532 42 65-89 377 584 30 34-01 378 584 28 77-01 DESCRIPTION Link Clutch Ground Drive Bellcrank Groundrive Nstg/Nstl Keeper Bellcrank Drive Ground Brake Bracket Washer 11/32 x 11/16 x 16 Ga. Washer 25/32 x 1-5/8 x 16 Ga. Pedal Brake Washer 13/32 x 13/16... Brake Parking Washer Harden .793 x 1.637 x 060 Cover Pedal Blk Round Bolt Rdhd 3/8-16unc x1-3/4 Gr.5 Idler.Flat Nut Hex Flangelock 3/8-16 Idler V-Groove Offset Belt Drive Shaft Asm. KEY PART NO. TRACTOR - YTA22V46 (96043021200), PRODUCT NO. 960 43 02 12...
... 68 06-00 376 532 42 65-89 377 584 30 34-01 378 584 28 77-01 DESCRIPTION Link Clutch Ground Drive Bellcrank Groundrive Nstg/Nstl Keeper Bellcrank Drive Ground Brake Bracket Washer 11/32 x 11/16 x 16 Ga. Washer 25/32 x 1-5/8 x 16 Ga. Pedal Brake Washer 13/32 x 13/16... Brake Parking Washer Harden .793 x 1.637 x 060 Cover Pedal Blk Round Bolt Rdhd 3/8-16unc x1-3/4 Gr.5 Idler.Flat Nut Hex Flangelock 3/8-16 Idler V-Groove Offset Belt Drive Shaft Asm. KEY PART NO. TRACTOR - YTA22V46 (96043021200), PRODUCT NO. 960 43 02 12...
Operation Manual
Page 6
...cutting results. (Tires must be properly leveled. TO ROLL TRACTOR OFF SKID (See Operation section for replacing motion and mower blade drive belts in safe operating condition. ✓ Ensure Operator Presence System and Reverse Operation System (ROS) are routed properly around pulleys and inside... that are properly inflated. (For shipping purposes, the tires were overinflated at the factory for leveling.) ✓ Check mower and drive belts. CHECK BRAKE SYSTEM After you start the engine. ✓ Ensure brake system is in the Service and Adjustments section of this manual...
...cutting results. (Tires must be properly leveled. TO ROLL TRACTOR OFF SKID (See Operation section for replacing motion and mower blade drive belts in safe operating condition. ✓ Ensure Operator Presence System and Reverse Operation System (ROS) are routed properly around pulleys and inside... that are properly inflated. (For shipping purposes, the tires were overinflated at the factory for leveling.) ✓ Check mower and drive belts. CHECK BRAKE SYSTEM After you start the engine. ✓ Ensure brake system is in the Service and Adjustments section of this manual...
Operation Manual
Page 17
...from steering plate. CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of engine. Except for the washout port (if equipped), we do not recommend using a dirty air filter. Clean with a blocked... it could create a fire hazard and/or damage. CLEAN AIR SCREEN The air screen is over the air intake blower located on top of drive. Ensure the cooling shrouds are properly positioned. • Immediately wipe up any spilled gasoline. CAUTION: Avoid all gasoline, oil, etc. •...
...from steering plate. CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of engine. Except for the washout port (if equipped), we do not recommend using a dirty air filter. Clean with a blocked... it could create a fire hazard and/or damage. CLEAN AIR SCREEN The air screen is over the air intake blower located on top of drive. Ensure the cooling shrouds are properly positioned. • Immediately wipe up any spilled gasoline. CAUTION: Avoid all gasoline, oil, etc. •...
Operation Manual
Page 22
...INSTALL MOWER" section in this manual.) NOTE: Observe entire motion drive belt and position of tractor. SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 32) The mower blade drive belt may also check brake by placing freewheel control in "transmission ...disengaged" position. Engage parking brake. TO REPLACE MOTION DRIVE BELT (See Fig. 33) Park the tractor on level surface. Engage parking brake. BELT REMOVAL 1. Remove belt from transaxle input pulley (D). 5. Remove belt upwards from stationary idler (A) and clutching idler (B). 3. ...
...INSTALL MOWER" section in this manual.) NOTE: Observe entire motion drive belt and position of tractor. SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 32) The mower blade drive belt may also check brake by placing freewheel control in "transmission ...disengaged" position. Engage parking brake. TO REPLACE MOTION DRIVE BELT (See Fig. 33) Park the tractor on level surface. Engage parking brake. BELT REMOVAL 1. Remove belt from transaxle input pulley (D). 5. Remove belt upwards from stationary idler (A) and clutching idler (B). 3. ...
Operation Manual
Page 27
...corrected. Blown fuse. 1. Turn switch "ON". 2. Poor cable connections. 3. Loss of mower housing. 8. Replace motion drive belt. 4. Install axle key at rear wheel. Turn ignition key to slower speed. 3. Faulty operator-safety presence control system.... Tighten blade bolt. 2. Obstruction in "FAST" position. 2. Worn/damaged mower drive belt. 3. Wet grass. 3. Mower deck not level. 4. Level mower deck. 5. Replace blade. Mower drive belt worn. 8. Replace mower drive belt. 9. Check/replace light switch. 4. Battery will not rotate Poor grass discharge ...
...corrected. Blown fuse. 1. Turn switch "ON". 2. Poor cable connections. 3. Loss of mower housing. 8. Replace motion drive belt. 4. Install axle key at rear wheel. Turn ignition key to slower speed. 3. Faulty operator-safety presence control system.... Tighten blade bolt. 2. Obstruction in "FAST" position. 2. Worn/damaged mower drive belt. 3. Wet grass. 3. Mower deck not level. 4. Level mower deck. 5. Replace blade. Mower drive belt worn. 8. Replace mower drive belt. 9. Check/replace light switch. 4. Battery will not rotate Poor grass discharge ...