Husqvarna TA48 Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna TA48 manuals!
Problems with Husqvarna TA48?
Ask a Question
Free Husqvarna TA48 manuals!
Problems with Husqvarna TA48?
Ask a Question
Popular Husqvarna TA48 Manual Pages
Operation Manual - Page 2
Printed U.S.A.
2 Beatrice, NE - ©2003 Husqvarna. All rights reserved.
Operation Manual - Page 3
... you have just purchased the 1.
Only a few
curred during shipment. simple steps are included in hole "B" near end of damage that all bolts, washers and
Husqvarna Towable Aerator - Please read these instructions before inserting into frame mount.
Tip aerator onto its back edge and install jack lift assembly.
See Figure 3.
3
Operation Manual - Page 4
...model only.)
5. Attach the tie bars to the aerator bed and
to the tow bar as seen in frame and attach jack assembly to highest position
7. Lower transport wheels fully before tipping aerator. Install tow...bolt will require the use of a 9/16" deep-well socket wrench to tipping aerator into frame mount and aligning holes. Align jack lift assembly hole "B" with socket
prior to tighten.
6.
See...
Operation Manual - Page 5
... NOTE: Park unit on a hard flat surface before towing the unit.
Always raise the kickstand before lowering kick stand. Before removing aerator from tractor may cause unit to the jack could result....
9. See Figure 8. Failure to lower kickstand before detaching unit from tractor and
storing, lower the kick stand (48" model ...
Operation Manual - Page 6
Remove weights from pan before unhooking aertor from tractor.
6 OPERATION When replacing worn or damaged tines, use included washers and torque to the limits shown in the specification section. Weights may be added into the pan if used on rough ground or on angled surface. Secure weights into pan to increase depth of ground penetration up to 15 ft./lbs.
Operation Manual - Page 7
...(Torque to 15 ft/lbs.) Lubricate wheels - every 25 hours. (Torque to 15 ft/lbs.) Lubricate wheels - every 100 hours. Check tine bolts - Width: 58 1/2" Length: 56 1/3" Aerating pattern: 4 3/4" x 7"
7 Minimum horsepower of towing vehicle - 16 H.P. Aerating pattern: 4 3/8" x 7" 48" MODEL: Maximum weight in pan - 300 lbs. SPECIFICATIONS
36" MODEL: Maximum weight in pan - 375 lbs.
Operation Manual - Page 9
...30 ...... 539109294 ........2 ...... DECAL, TA48 AERATOR (NOT SHOWN 539108429 ........2 ...... AXLE PIVOT BUSHING 6 ........ 539990563 ........4 ...... HCS 1/2-13 X 3 1/2, GR5 9 ........ 539990550 ........2 ...... TIE BAR 13 ...... 539007562 ........2 ...... DECAL, HUSQVARNA (NOT SHOWN 539104789 ........2 ...... TA48CE
ITEM PART NO. DESCRIPTION
1 ........ 539990553 ........1 ...... NUT...
Operation Manual - Page 11
... 539007566 ..... 2 ..... FASTENER KIT, CORING TINE SET 9 ........ 539101572 ..... 2 ..... JACK W/ BOLT KIT .......... 539007555 ..... 1 ..... TILT WHEEL 5 ........ 539007500 ..... 2 ..... DESCRIPTION 1 ........ 539000317 ..... 4 ..... TOW BAR W/ BOLT KIT 12 ...... 539200165 ..... 1 ..... BEARING W/COLLAR 2 ........ 539007562 ..... 2 ..... QTY. TINE SET (16 PER ROTOR) 8 ........ 539007574...
Husqvarna TA48 Reviews
We have not received any reviews for Husqvarna yet.