Husqvarna K 1260 16 Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna K 1260 16 manuals!
Problems with Husqvarna K 1260 16?
Ask a Question
Free Husqvarna K 1260 16 manuals!
Problems with Husqvarna K 1260 16?
Ask a Question
Popular Husqvarna K 1260 16 Manual Pages
Owners Manual - Page 1
RIDER 970
RIDER 850
RIDER 850
Rider 850 HST Rider 970 HST
Operator´s manual
Please read these instructions carefully and make sure you understand them before using the machine.
101 89 36-26
Owners Manual - Page 3
...Trouble shooting schedule 29 Storage 30 Winter storage 30 Service 30 Technical data 31
IMPORTANT INFORMATION
Read through these instructions carefully so that you know how to use and maintain the machine before using it. For servicing other than described in this manual...the battery acid level 21 Checking the safety system 21 Replacement of air filter 22 Checking and adjustment of cutting ...
Owners Manual - Page 9
PRESENTATION
Presentation
These instructions describe two machine models, Rider 850 and Rider 970.
There is available with three different ...65
4
3
2
1
12
78
9
Location of the controls
1. Speed limiter for parking brake 9. Fuel tank cap 11. Both models are fitted with the foot pedals.
Ignition lock 2. Brake pedal 8. Main lock (under seat) 12. RIDER 850
RIDER 850
RIDER ...
Owners Manual - Page 15
... started release the ignition key to start , wait about 5 seconds at a time.
Never run the starter for more than about 10 seconds before trying again.
6. Set the throttle control midway between position
1 and 2.
1
2 3
5. IMPORTANT INFORMATION Do not run the engine indoors, in enclosed or poorly ventilated areas.
Owners Manual - Page 17
... a uniform cutting height it is important that the tyre pressures are equal on the lift lever and lower down the cutting unit. IMPORTANT INFORMATION The service-life of the drive belts increases considerably if the engine is cut often. For this reason do not increase the throttle until the required cutting...
Owners Manual - Page 18
... the engine to idle for a minute to move the machine when the engine is switched off the release lever must be pressed down and forwards.
16 -
STOP START
Release lever
In order to obtain normal working temperature before stopping it if it has been working hard. 1.
Owners Manual - Page 19
...cable is removed from the plug.
q = Described in these instructions.
! WARNING! r
Replace the air filter's pre-filter and paper filter 2)
22
q
Replace the fuel filter
28
q
Replace the plug
-
r
Check the hydrostat's cooling fins
- r = Not described in these instructions go to an authorised service workshop. For the items which should be conducted on the machine...
Owners Manual - Page 20
... hood Release the screws in the fender (2) and lift off the hood.
MAINTENANCE
Dismantling of the machine hoods
Engine hood The engine is accessible for servicing when the engine hood is lifted up.
Owners Manual - Page 24
...filter in a clean cloth. IMPORTANT INFORMATION Do not use compressed air to clean the paper filter.
5. Replace the plastic cover oven the air filter housing and tighten the wing-nut.
22 - Fit the air... off the paper filter with dirt. It is replaced as follows: 1. Remove the wing-nut on page 17 for correct service interval).
MAINTENANCE
Replacing the air filter
If the engine seems to lack...
Owners Manual - Page 25
...of the unit, at the front and back of the cutting unit as follows: 1. Place a set of the cutting unit's ground pressure Rider 970
To achieve the best cutting results the cutting unit ...
Checking and adjustment of bathroom scales under the cutting
unit's frame (front edge) so that the support wheels do not bear any weight.
2. Adjusting of the machine. The ground pressure should follow the...
Owners Manual - Page 27
...Rider 850 HST as follows:
1. WARNING!
Dismantle the front hood as described on page 18.
2. Set the cutting height to the transport position.
3. Push the stop (1) in the lift lever's lock button...edge of the cutting unit takes place in the reverse order to cutting position, and then setting the lowest cutting height with the cutting height lever.
5.
Push the lock-plate (4) forwards...
Owners Manual - Page 28
.../cm2).
English The maximum tyre pressure is important that the blades' attachment screws are undamaged and well-sharpened. IMPORTANT INFORMATION Replacing or sharpening the blades should be conducted by an authorised service workshop. Otherwise the blades can be as shown in the blades cutting the grass at different heights.
26 -
IMPORTANT INFORMATION...
Owners Manual - Page 31
.... • Dirt in carburettor or fuel pipe. Engine does not run smoothly.
• Wrong gear, too high. • Carburettor incorrectly set .
TROUBLE SHOOTING SCHEDULE
Problem
Engine will not start.
English - 29 Engine overheats.
• Engine overloaded. • Air intake or cooling flanges blocked. • Fan damaged. • Too little or ...
Owners Manual - Page 32
...oil, and take care of fuel.
5. Empty the fuel tank. Service
When ordering spare parts state the purchase year, model, type, and serial number.
If alkylate petrol (Aspen) is used ...with the engine. However, one should immediately be put the machine in order for storage follow these instructions:
1.
English It is left to stand for more ) can leave tacky deposits which is highly ...
Owners Manual - Page 33
...parts are valid on the basis of information in this manual...16 x 6.50 x 8 60 kPa (0.6 kp/cm2)
15°
Rider 970
2145 mm 1050 mm (970-15.5), 1260... mm (970-15.5S) 1120 (970-Bioclip) 1060 mm 240 kg 855 mm Front 715 mm, rear 625 mm 16 x 6.50 x 8 60 kPa (0.6 kp/cm2)
15°
Briggs & Stratton model...We reserve the right to change technical specifications without prior notice. English - 31 TECHNICAL...
Husqvarna K 1260 16 Reviews
We have not received any reviews for Husqvarna yet.