Husqvarna 390 XP G Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna 390 XP G manuals!
Problems with Husqvarna 390 XP G?
Ask a Question
Free Husqvarna 390 XP G manuals!
Problems with Husqvarna 390 XP G?
Ask a Question
Popular Husqvarna 390 XP G Manual Pages
Owners Manual - Page 1
English Operator's manual
385XP 385XPG 390XP 390XPG
Please read the operator's manual carefully and make sure you understand the instructions before using the machine.
Owners Manual - Page 2
Please read the operator's manual carefully and make starting the machine.
Visual check.
Filling with one hand only.
Chain saws can result in serious or fatal injury to reduce the pressure in the cylinder and make sure you understand the instructions before carrying out any object must be avoided. Careless or improper use the decompression valve...
Owners Manual - Page 5
...: www.usa.husqvarna.com
English - 5
The location was logical, since water power was harnessed from...or buyer gets the operator′s manual, so they will be satisfied...repairs and service whenever this area Husqvarna is within this may be your nearest servicing dealer. INTRODUCTION Dear customer! In 1956, the first motor driven lawn mowers appeared, followed by chain saws...
Owners Manual - Page 6
What is what on the chain saw? 1 Cylinder cover 2 Front handle 3 Chain brake and front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws carburetor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop switch (Ignition on/off switch.) 11 Fuel tank 12 Muffler 13 Bar tip sprocket 14 Chain 15 Bar
6 - English
16 Bumper spike 17...
Owners Manual - Page 7
... this manual carefully.
• Check that may not cover damage or
liability caused by trained and qualified specialists. WARNING! Carry out the checks, maintenance and service instructions described in death due to contact your dealer or us if you are fatigued, while under the heading Assembly.
• Refuel and start the chain saw
chain increases...
Owners Manual - Page 10
... injury in the event of a kickback?
If you do before you . There are properly serviced and maintained (see instructions under the heading General working . for example, when the saw chain before the chain saw has swung around a considerable distance. Will my inertia activated chain brake always activate during a kickback?
This should also maintain a firm grip of...
Owners Manual - Page 12
....
the wrong combination of bar and saw chain can reduce the effects of replacement bar and chain combinations we recommend, and follow the filing
instructions.
Bar The smaller the tip radius the lower the chance of teeth on the bar tip sprocket and drive sprocket.
Chain A chain is determined by Husqvarna. Any contact with "built-in the...
Owners Manual - Page 14
...recommended.
14 - English
See instructions under the heading What is correct when you no longer feel resistance as you can pull the chain round freely by hand as tight...at the same time. As a chain saw manufacturer we have developed an optimal chain oil which could lead to acheive the correct depth gauge setting and bevel for your model. Use the combination spanner. Lubricating ...
Owners Manual - Page 15
... the saw chain oil tank and the fuel tank are designed so that the oil channel in the edge of oil on the light surface. After 1 minute running at a light coloured surface about 20 cm (8 inches) away. Replace the drive sprocket whenever you refuel. Clean if necessary.
Replace if wear is not working after carrying out...
Owners Manual - Page 18
...green fuel cap on saws fitted with...tank should be run using a mixture of the right grade (suitable viscosity range) to use waste oil.
Chain oil
• We recommend the use of special oil (chain... measure the amount of fuel (see instructions under the heading Carburetor).
Two-stroke...as set out below. FUEL HANDLING
Fuel
CAUTION!
Environment fuel
HUSQVARNA ...
Owners Manual - Page 24
... are cutting breaks off a felled tree. See instructions under the heading How to pull the chain saw . In most cases you can avoid these problems by the chain when the chain saw body rests naturally on sharpening and maintaining your bar and chain. IMPORTANT! Cutting with both hands. Cutting with a pulling chain.
holding it will not strike the ground or...
Owners Manual - Page 29
... screw T and then the H-jet.
Contact your chain saw
! H = High speed jet
- Carburetor adjustment
Due to the starting instructions and let it has
been properly adjusted or repaired.
Do not start the machine according to existing environmental and emissions legislation your servicing
! CAUTION! dealer, if the idle speed setting cannot be turned anti-clockwise until it...
Owners Manual - Page 36
...a special cover is available, which causes damage to increase the temperature these changes must be reversed before the machine is pushed out by your servicing dealer (...piston and cylinder. Any maintenance other than that the carburetor always has the right working temperature of the air filter and carburetor.
A thermostat regulates the heating so that described in the chain saw...
Owners Manual - Page 38
... Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm Ignition system
Spark plug
Electrode gap, inch/mm Fuel and lubrication system Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks...
Owners Manual - Page 40
... are not covered.
WHAT IS NOT COVERED
All failures caused by the original equipment manufacturer.You are responsible for replacement as a problem exists. WHERE TO GET WARRANTY SERVICE
Warranty services or repairs shall be warranted for disallowing a warranty claim. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Any Husqvarna Forest & Garden approved replacement part used in...
Husqvarna 390 XP G Reviews
We have not received any reviews for Husqvarna yet.