Manual
Page 6
... of the turbo tool to end of cord. HOW TO USE Cleaner Description 2.1 1. Self-Propel Button 2 3. Hose 3 5. Handle Release Lever 9. Crevice Tool* *Accessories not included with other wand. 1.8 1.9 Snap dusting brush (H), crevice tool (I) and furniture nozzle (J) into storage area on back of cleaner. ... at the top. To turn cleaner OFF, push switch down. 2.2 Actual model may be purchased separately by visiting www.hoover.com, or your local HOOVER® service center. ON-OFF Switch 4. Edge Groomers 19 10. Brushroll Control 7 20 12. Cord Hooks 19. ...
... of the turbo tool to end of cord. HOW TO USE Cleaner Description 2.1 1. Self-Propel Button 2 3. Hose 3 5. Handle Release Lever 9. Crevice Tool* *Accessories not included with other wand. 1.8 1.9 Snap dusting brush (H), crevice tool (I) and furniture nozzle (J) into storage area on back of cleaner. ... at the top. To turn cleaner OFF, push switch down. 2.2 Actual model may be purchased separately by visiting www.hoover.com, or your local HOOVER® service center. ON-OFF Switch 4. Edge Groomers 19 10. Brushroll Control 7 20 12. Cord Hooks 19. ...
Manual
Page 9
... hand tool may be used to give extra length to prevent the cleaner from images shown. Twist wand or tool slightly to hose tube (A). Dusting brush may vary from falling, always place cleaner at bottom of the above tools. B. Attach wand and tools 2.14 2.14 Attach any of stairs or on...
... hand tool may be used to give extra length to prevent the cleaner from images shown. Twist wand or tool slightly to hose tube (A). Dusting brush may vary from falling, always place cleaner at bottom of the above tools. B. Attach wand and tools 2.14 2.14 Attach any of stairs or on...
Manual
Page 14
.... Belt will "pop" into the rectangular slot (G) on belt and "snap" it should be purchased at Hoover.com or 1-800-944-9200. If desired, additional belts can start suddenly. When brushroll brushes are worn, it out. How to Remove 3.17 Slide Brushroll Control (Fig. 2.9) to last for...Discard used belt and replace. Positioning Belt on Brushroll Before positioning belt onto brushroll, check for HOOVER® part No. 48414144. Agitator brushroll can be replaced. 3.16 To check condition of brushes, move the edge of a card across bottom plate while turning brushroll. How to pulley. ...
.... Belt will "pop" into the rectangular slot (G) on belt and "snap" it should be purchased at Hoover.com or 1-800-944-9200. If desired, additional belts can start suddenly. When brushroll brushes are worn, it out. How to Remove 3.17 Slide Brushroll Control (Fig. 2.9) to last for...Discard used belt and replace. Positioning Belt on Brushroll Before positioning belt onto brushroll, check for HOOVER® part No. 48414144. Agitator brushroll can be replaced. 3.16 To check condition of brushes, move the edge of a card across bottom plate while turning brushroll. How to pulley. ...
Manual
Page 17
... belt. Slide button to Incorrect carpet height setting. Replace belt Continue using the checklist below. Check items under "Cleaner won 't self-propel Brushroll not turning Flat belt broken or worn. WARNING ! Thermal protector activated. Agitator is found by an authorized service representative. !...when the cause is obstructed. Allow cleaner to carpet position. Replace belt. To reduce risk of personal injury - Agitator brushes Custom Control™ switch set Set switch to cool for 30 minutes (this will reset the thermal protector). Move carpet ...
... belt. Slide button to Incorrect carpet height setting. Replace belt Continue using the checklist below. Check items under "Cleaner won 't self-propel Brushroll not turning Flat belt broken or worn. WARNING ! Thermal protector activated. Agitator is found by an authorized service representative. !...when the cause is obstructed. Allow cleaner to carpet position. Replace belt. To reduce risk of personal injury - Agitator brushes Custom Control™ switch set Set switch to cool for 30 minutes (this will reset the thermal protector). Move carpet ...
