Hoover U5180-910 - Mach3 Cyclonic Upright Bagless Vacuum Support and Manuals
Get Help and Manuals for this Hoover item
View All Support Options Below
Free Hoover U5180-910 manuals!
Problems with Hoover U5180-910?
Ask a Question
Free Hoover U5180-910 manuals!
Problems with Hoover U5180-910?
Ask a Question
Most Recent Hoover U5180-910 Questions
How To Remove Vacuum Belt From A Hoover Mach 3
(Posted by helencvd 9 years ago)
How Do You Empty Cyclender?
(Posted by dnmerrick 10 years ago)
Hoover Mach 5 Wont Stand Up What Part Do I Need
(Posted by amandaprill33 11 years ago)
Hoover Mach 3 Has No Suction. What Do I Do?
(Posted by dirtgirl 11 years ago)
Wheels
Needing to replace the Wheel-Housing so how do I remove the wheels from the broken one to install on...
Needing to replace the Wheel-Housing so how do I remove the wheels from the broken one to install on...
(Posted by Zinda56 11 years ago)
Popular Hoover U5180-910 Manual Pages
Manual - Page 1
®
Cyclonic Upright
®
Vacuum Cleaner
hoover.com
Owner's Manual
ENGLISH § pp. 1-12 ESPAÑOL § pág 13-20 FRANÇAIS § p. 21-27
This product was designed for easy assembly (see page 3)
Review this manual before operating the cleaner.
Manual - Page 2
... Service 11 Cleaning Filters 7-8 Clearing Blockages 12 Emptying Dirt Cup 6-7 Replacing Agitator Brush Roll ........9 Replacing Belt 8-9 Replacing Powered Hand Tool
Agitator Brush Roll 10 Replacing Power Hand Tool Belt ..10 Replacing Headlight 8 Thermal Protector 11 Warranty 12 Parts & accessories mail order form 29
© 2005 The Hoover Company hoover.com
2
Important Safeguards! Model...
Manual - Page 3
...*
*NOTE: Three (3) wands and the floor
A
brush available on the "Service" button to the store.
1.
Grasp orange tie wrap (A) and pull until step...
disposing of the handle cavity. Press button (F) at hoover.com.
Cleaner body C.
only) OR Call 1-330-...and push handle all parts from carton and
B
identify each item shown. Click on some models
only. Cleaner assembly
Carton ...
Manual - Page 4
... for height of carpet being
cleaned. Dirt cup assembly
21. Dirt cup door hinge
step on lever to correct setting plate on back of cleaner as shown.
2.
prevent cleaner from room to install the proper outlet. Hose handle 14. If the plug does not fit fully in any way. Do not change...
Manual - Page 5
... cleaning handle (A) and guide cleaner with other end or edge. Cleaning lightweight
flexible rugs
Stand on one end of rug and move into the adjusted position until the cleaner handle is lowered to the operating position.
2-7
2-8
2-9
A
Settings
For maximum cleaning performance, the following carpet height settings are recommended:
• Lowest setting: for all types...
Manual - Page 6
... tipping cleaner or setting it firmly onto ...tool may be in such places as shown. Floor brush (available on tool. To replace brushes, align bottom of the above the floor and for reaching hard to hose ...may be sure the hose tube cover (C) is in warm water with grooves (K) on some models only) use . H.
Cleaning tools
Tools allow for cleaning surfaces above tools.
The cleaner is...
Manual - Page 7
... in place.
3-8
D
B A
C
Remove dirt cup as described in order for 24 hours before replacing filters into cleaner body.
3-7
A B
C
Dirt and debris can be emptied before the dirt reaches ...to empty
It is recommended that the dirt cup be cleaned from electrical outlet. Cleaning filters
Cyclonic filter assembly
How to empty
Disconnect cleaner from frame. Do not use if preferred. Remove ...
Manual - Page 8
..., remove the the screw as described in good condition. Final filter assemby, HOOVER part No. 93002521. Replace belt if it is in Fig. 3-2.
Pull filter frame (A) straight out from ...belt, ask for : Secondary filter-white fabric filter, HOOVER part No. 93002520. Do not operate cleaner without dirt cup or filters in place.
3-9
A
B
Remove dirt cup as shown and lift off lens.
3-11
Installing...
Manual - Page 9
... toward front of belt, slide new belt over motor pulley (B).
3-17
3-18
3-19
E
D
F
C
Replacing agitator brush roll Insert agitator through belt and place belt in belt guide (C) on agitator. Installing new belt
With lettering on hood with Fig. 3-13. Turn agitator making sure belt turns freely and is equipped with bearings that contain sufficient lubrication for HOOVER part No. 48414115...
Manual - Page 10
... place. 5. How to pinch brush bristles in guard. However, if the belt is in Figs. 3-23 through 3-26. Replace belt
When replacing belt, ask for HOOVER part No. 48414088.
3-21
A
3-22
B
2. Remove bottom plate, belt guard and brush roll as described in good condition. Replace brush roll, belt guard, and bottom plate as described in tool housing and snap into...
Manual - Page 11
...; Blockage in turbine channel • Remove blockage.
• Broken or worn belt • Replace belt
• Low cleaner suction • Check items under "Vacuum Cleaners Household" OR • checking the list of Sales and Service Centers provided with this will reset the thermal protector)
Problem: Cleaner/tools won 't run
Possible Cause Possible Solution • Not firmly plugged...
Manual - Page 12
... remove. 10. S. Proof of parts only. Appliances purchased elsewhere are questions concerning this warranty gives you specific legal rights, you mail your appliance to the following authorized warranty service outlets.
This warranty does not apply if the appliance is suction, continue with each step until the blockage is rendered.
1. Replace belt, agitator and hood...
Hoover U5180-910 Reviews
Hoover has a rating of 4.00 based upon 1 review.
Get much more information including the actual reviews and ratings that combined to make up the overall score listed above. Our reviewers
have graded the Hoover U5180-910 based upon the following criteria:
- Durability [1 rating]
- Cost Effective [1 rating]
- Quality [1 rating]
- Operate as Advertised [1 rating]
- Customer Service [1 rating]