Hoover U5180-910 Support Question
Hoover U5180-910 Support Question
Find answers below for this question about Hoover U5180-910 - Mach3 Cyclonic Upright Bagless Vacuum.Need a Hoover U5180-910 manual? We have 1 online manual for this item!
Question posted by Zinda56 on December 15th, 2012
Wheels
Needing to replace the Wheel-Housing so how do I remove the wheels from the broken one to install on the new one?
Current Answers
Related Hoover U5180-910 Manual Pages
Manual - Page 1
®
Cyclonic Upright
®
Vacuum Cleaner
hoover.com
Owner's Manual
ENGLISH § pp. 1-12 ESPAÑOL § pág 13-20 FRANÇAIS § p. 21-27
This product was designed for easy assembly (see page 3)
Review this manual before operating the cleaner.
Manual - Page 2
...12 Emptying Dirt Cup 6-7 Replacing Agitator Brush Roll ........9 Replacing Belt 8-9 Replacing Powered Hand Tool
Agitator Brush Roll 10 Replacing Power Hand Tool Belt ..10 Replacing Headlight 8 Thermal Protector 11 ... and Service Center or Authorized Hoover Warranty Service Dealer (Depot). • Use vacuum cleaner only for choosing a HOOVER® product
Please enter the COMPLETE model and...
Manual - Page 3
...tools and wands
*
*NOTE: Three (3) wands and the floor
A
brush available on the back of the handle housing. Grasp orange tie wrap (A) and pull until step 1-3 is complete.
1-4
Hold plug (B) with one way....tie wrap (A) must be removed. only) OR Call 1-330-499-9499 to the store.
1. Cleaner body C. Note: The plug will only fit together one hand; If you need any assistance:
Visit our ...
Manual - Page 4
... cord into bottom of rack. To turn cleaner ON, push ON/OFF switch once. How to install the proper outlet. Snap wand
into the desired position.
2-3
Transporting cleaner
To move your cleaner, ...18
7
14
8
20
9 13
10
11
1. If the plug does not fit fully in upright position, tilt cleaner back on back of dirt cup. 17 10. prevent cleaner from room to correct setting plate on ...
Manual - Page 5
...The handle of carpet. Note: If the cleaner is desired, while maintaining good cleaning performance.
upright for very deep pile carpet, where easier pushing effort is difficult to push, turn knob to... the desired setting. Stair cleaning
A stair cleaning handle has been designed for ease in upright position and turn the nozzle control knob (B) to the next higher setting.
• Higher ...
Manual - Page 6
...to your hose. Remove brush to remove.
Twist wand or tool slightly to rotate while cleaner handle is in upright position. Also, turn cleaner OFF before using.
2-10
B
A
C
Removing hose
When using ...warm water with a cloth dampened in the upright position.
Combination tool use when handle is in such places as shown. To replace brushes, align bottom of the above the ...
Manual - Page 7
Cleaning filters
Cyclonic filter assembly
How to secure into position. Pivot cup into cleaner body.
3-7
A B
C
Dirt and debris can be emptied before replacing filters into place.... from electrical outlet. Remove assembly from frame. Press on dirt cup release button while firmly pressing on latch (A) located at the top of dirt cup cavity. 3. Replace dirt cup as described...
Manual - Page 8
...Installing bulb Pull old bulb straight out of dirt cup cavity. Do not attempt to remove filter (B) from electrical outlet. What to buy
When purchasing new filters, ask for HOOVER part No. 38528040 (belt package part No. 40201190).
3-13
A
A
How to replace... or broken. What to buy
This cleaner uses a 13 volt, T-3 114 wedge base bulb, Hoover part No. 27313107.
3-10
Removing lens Disconnect cleaner ...
Manual - Page 9
...). To check condition of cleaner and remove the hood. Discard old agitator. To maintain cleaning effectiveness, replace agitator if brushes do not add lubricant to reposition belt, new agitator and hood. Installing new belt
With lettering on outside of belt, slide new belt over motor pulley (B).
3-17
3-18
3-19
E
D
F
C
Replacing agitator brush roll Insert agitator through belt...
Manual - Page 10
... is cracked, gouged or broken, it so bottom faces up. How to pinch brush bristles in tool housing and snap into slots on front of brush roll into slots (E) on edge of bottom plate into place. 5. Remove agitator including end plates (C) and discard. 4. Replace belt guard (B) making sure not to replace
1. Replace with new belt.
8. Pivot bottom...
Manual - Page 11
... minutes, the thermal protector automatically resets and cleaning may need servicing (see "Service" section). When the thermal protector activates, the cleaner will only result in turbine channel • Remove blockage.
• Broken or worn belt • Replace belt
• Low cleaner suction • Check items under "Vacuum Cleaners Household" OR • checking the list of...
Manual - Page 12
...on back of one way. Remove bottom plate, belt guard and turbine as described in and turn ON. Remove any blockage.
4-2
C
Checking airflow path through 3-15). Replace belt turbine, brush roll, ...Clearing blockages
Disconnect cleaner from hose. Low suction or pick up , delivery, or house calls; empty if needed , or if there are covered by presenting the appliance to state. Plug cleaner...
Similar Questions
My Hoover Upright Bagless Vacuum's Suction Doesn't Work.
(Posted by ljbennion50 11 years ago)
Hoover U5180-910 Mach 3 Cyclonic Upright
How do you empty the contents when full?
How do you empty the contents when full?
(Posted by bobf537 12 years ago)
How To Switch From Using Floor Clean To Using Hose On Hoover Cyclonic Upright.
I got a hoover cyclonic upright bagless vacuum used with no instructions. Is there a way to switch t...
I got a hoover cyclonic upright bagless vacuum used with no instructions. Is there a way to switch t...
(Posted by mindy 12 years ago)
Hoover Cyclonic Upright Series U5180
It blew the house circuit breaker and now won't restart. It is not clogged and filters clean. I bypa...
It blew the house circuit breaker and now won't restart. It is not clogged and filters clean. I bypa...
(Posted by dmcgee 13 years ago)