Service Manual
Page 3
... diagram for Sparking and Corrective Action 26 9-4. SPECIFICATIONS ...2 5-1. Nail Driving Force ...4 6. Warning Label ...6 7-3. Troubleshooting and Correction ...19 9-3. Disconnection and Reconnection of the Nailing Action ...2 5-3. Specifications ...2 5-2. COMPARISONS WITH SIMILAR PRODUCTS 5 7. TROUBLESHOOTING GUIDE ...16 9-1. SELLING POINTS ...1 5. Explanation of Wiring between Cylinder Head Section and Handle Section ...31 10-3. Related Laws and Regulations ...8 8. INSPECTION AND CONFIRMATION...
... diagram for Sparking and Corrective Action 26 9-4. SPECIFICATIONS ...2 5-1. Nail Driving Force ...4 6. Warning Label ...6 7-3. Troubleshooting and Correction ...19 9-3. Disconnection and Reconnection of the Nailing Action ...2 5-3. Specifications ...2 5-2. COMPARISONS WITH SIMILAR PRODUCTS 5 7. TROUBLESHOOTING GUIDE ...16 9-1. SELLING POINTS ...1 5. Explanation of Wiring between Cylinder Head Section and Handle Section ...31 10-3. Related Laws and Regulations ...8 8. INSPECTION AND CONFIRMATION...
Service Manual
Page 19
.... 13). Press the Pushing Lever [64] securely. Top Cover [3] Filter [4] (Clean the Filter [4] with a flat-blade screwdriver. 9. TROUBLESHOOTING GUIDE 9-1. Problems Caused by abnormality of fuel. These problems are not caused by Improper Handling Following table shows the problems that are insufficient. Please... instruct the customers to use the nailer properly according to the nailer. Improper handling Problem Cause Remedy The Trigger [98] is set improperly. The Pushing Lever [64] is...
.... 13). Press the Pushing Lever [64] securely. Top Cover [3] Filter [4] (Clean the Filter [4] with a flat-blade screwdriver. 9. TROUBLESHOOTING GUIDE 9-1. Problems Caused by abnormality of fuel. These problems are not caused by Improper Handling Following table shows the problems that are insufficient. Please... instruct the customers to use the nailer properly according to the nailer. Improper handling Problem Cause Remedy The Trigger [98] is set improperly. The Pushing Lever [64] is...
Service Manual
Page 22
... and the Motor [6]. Replace the Pushing Lever [64]. Replace the Motor [6]. --- 19 --- Check the position of fuel in the case of gas nailers The mechanism of the temperature and the altitude. The Pushing Lever [64] cannot be pushed up. The O-ring [15] is deformed. The ... [82] is pinched. The Motor [6] is faulty. Replace the Switch Arm [82]. Troubleshooting and Correction (1) Troubleshooting and correction in the fuel cell. Short of the Piston [39]. Low voltage. Break in gas nailers. Set the metering valve to 40ûC Altitude: Under 1500 m (5000 feet) Set...
... and the Motor [6]. Replace the Pushing Lever [64]. Replace the Motor [6]. --- 19 --- Check the position of fuel in the case of gas nailers The mechanism of the temperature and the altitude. The Pushing Lever [64] cannot be pushed up. The O-ring [15] is deformed. The ... [82] is pinched. The Motor [6] is faulty. Replace the Switch Arm [82]. Troubleshooting and Correction (1) Troubleshooting and correction in the fuel cell. Short of the Piston [39]. Low voltage. Break in gas nailers. Set the metering valve to 40ûC Altitude: Under 1500 m (5000 feet) Set...
Service Manual
Page 26
... injection port of Nail Feeder (A) [112]. Nail Rail [93] is not loaded with abnormal nails (bent nails, large or small round-head nails, abnormal collation, etc.). Check if nails (one strip) move smoothly in the magazine. Remove the abnormal nails and load the magazine ...specified genuine nails. Nail inlet groove of general-purpose nailers Problem Possible cause Inspection method 1) Nails cannot be driven. Remove the adhesive fragments and apply oil to the nail feeder, Ribbon Spring [121] and the nail rail. (2) Troubleshooting and correction in the case of the nose is...
... injection port of Nail Feeder (A) [112]. Nail Rail [93] is not loaded with abnormal nails (bent nails, large or small round-head nails, abnormal collation, etc.). Check if nails (one strip) move smoothly in the magazine. Remove the abnormal nails and load the magazine ...specified genuine nails. Nail inlet groove of general-purpose nailers Problem Possible cause Inspection method 1) Nails cannot be driven. Remove the adhesive fragments and apply oil to the nail feeder, Ribbon Spring [121] and the nail rail. (2) Troubleshooting and correction in the case of the nose is...