Hitachi DH40FA - 1-9/16" Spline Shank Rotary Hammer Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi DH40FA manuals!
Problems with Hitachi DH40FA?
Ask a Question
Free Hitachi DH40FA manuals!
Problems with Hitachi DH40FA?
Ask a Question
Popular Hitachi DH40FA Manual Pages
Instruction Manual - Page 3
... are outlined in the "SAFETY" section of the operating instructions, safety precautions and warnings in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in this Instruction Manual. Most accidents that the planned use this power tool in a manner that has not been specifically recommended by HITACHI, unless you and others. MEANINGS OF SIGNAL WORDS
WARNING...
Instruction Manual - Page 4
... with a polarized plug (one blade is grounded. (3) Don't expose power tools to rain or wet conditions. SAVE THESE INSTRUCTIONS
1. Water entering a power tool will fit in a polarized outlet only one way. Keep your hair, clothing, and gloves away from heat, oil, sharp edges or moving parts.
4 Cluttered benches and dark areas invite accidents. (2) Do not operate...
Instruction Manual - Page 5
... tools with care. Follow instructions in tools that is designed. (3) Do not use only identical replacement parts. Holding the work by unqualified personnel could result in the hands of untrained users. (6) Maintain tools with your finger on invites accidents.
(4) Remove adjusting keys or wrenches before resuming operation of the tool.
5 A wrench or a key that have the tool serviced...
Instruction Manual - Page 6
..., bolts, and plates tightly mounted. Do not use tool for repairs by children, individuals unfamiliar with solvent. Operate power tools at a higher voltage than those specified. If the tool appears to the instructions provided herein. Turn power off. English
8. Do not wipe plastic parts with its nameplate. Don't use power tools if the plastic housing or handle is defective or...
Instruction Manual - Page 8
... effective, follow the normal
electrical safety precautions given in this power tool, and only genuine HITACHI replacement parts should be installed. English
DOUBLE INSULATION FOR SAFER OPERATION
To ensure safer operation of the power tool only with a soft cloth moistened with soapy
water, and dry thoroughly.
SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS OF THIS...
Instruction Manual - Page 9
... the power tool. NAME OF PARTS
Stopper
Side Handle
Switch Trigger
Tool Holder
OO
ED
Selector Lever Housing
Tail Cover Set Screw (Under the Tail Cover)
Fig. 1
Handle Nameplate
Brush Cap (Inside the Tail Cover)
SPECIFICATIONS
Motor Power Source Current Capacity
No-Load Speed Full-load Blow Weight
Single-Phase, Series Commutator Motor.
Some illustrations in this Instruction Manual...
Instruction Manual - Page 10
... is placed under appropriate conditions conforming to install dust cover (Fig. 2) Always install the dust cover on the product nameplate.
2. Confirming condition of sufficient thickness and rated capacity (refer to be replaced or repaired.
4. Power source Ensure that the switch is in the groove. Power switch Ensure that the power source to page 9). The extension cord should...
Instruction Manual - Page 11
... to install tool
&CAUTION: For tools such as a drill bit and a bull point, use only Hitachi genuine parts.
(1) Clean, then smear the tool shank with a safety clutch, if the drill bit becomes bound in reaction. Fully insert the tool shank into the hexagonal hole of the front cover. (Fig. 3)
(3) Return the tool holder to forcibly press the
rotary hammer main body...
Instruction Manual - Page 13
... shank adaptor. (1) Install drill bit with taper shank in the
taper shank adaptor. (2) Turn the power on and drill a base hole. (3) After cleaning out dust with a syringe,
attach the plug to the anchor tip and drive in the anchor with a manual hammer. (4) To remove the drill bit with taper shank, insert a cotter into the guide plate until it...
Instruction Manual - Page 15
... cause motor malfunctioning and degraded efficiency, replace the drill bit with oil or water.
4. When an auto-stop carbon brush is the very "heart" of the screws be loose, retighten them immediately. Should any of the power tool. shown in Fig. 17
15
When they are consumable parts. Inspecting the drill bits Since use of a dull...
Instruction Manual - Page 16
... assure that only authorized replacement parts will eventually require servicing or replacement of parts because of HITACHI Electric Hammer Grease A (standard accessory, contained in tube) to prevent lubricant leakage. How to install the tail cover with securely tightening two set screws and remove the tail cover. O Grease replacement period After purchase, replace grease after every 6 months...
Instruction Manual - Page 17
... separately
For accessories in this power tool are subject to change without any other attachment or accessory can be dangerous and could cause injury or mechanical damage. The use of any obligation on the part of the HITACHI. Anchor hole drilling Rotation + Hammering) 0
(3) Cotter (Code No. 944477)
Code No. 985374 985375 985376
`22_111=
0
(1) Drill bit (Taper shank)
(2) Taper shank...
Parts List - Page 1
HITACHI
LIST NO.
C
55 56 57 58
87 88 91
89 90
41 42
92 93
0
102 103 0 105
95
ric
mm
101
98 E435
ELECTRIC TOOL PARTS LIST
■ HAMMER DRILL Model DH 40FA
1997 • 2 • 20 (El)
5
3 2 1
7
43 44
10 12
45 46 47 48 49
0 50
54
59
502 503 504
C to
71 62
...
Parts List - Page 4
...SAF
1 EXCEPT FOR AUS,SAF
DH 40FA
STANDARD ACCESSORIES
ITEM NO. CODE NO.
USED
501 313-097 CASE (PLASTIC)
1
502 981- 840 GREASE (A) FOR NAMMER.HAMMER DRILL (300)
1
503 944- 458 HEX. DESCRIPTION
NO. TAPER SHANK... BIT 50MM
1 INCLUD.608
608 985- 388 GUIDE PLATE (FOR CORE BIT 50MM)
1
609 955- 159 , CORE BIT 105MM
1 INCLUD.610
610 955- 169 ' GUIDE PLATE (FOR CORE BIT 105MM)
1
611 955...
Parts List - Page 5
USED
1 1 1 1 1 1 1 1 1
REMARKS
DH 40FA
2-97
*: ALTERNATIVE PARTS DESCRIPTION
613 985- 379 CORE BIT SHANK D38 (1 - 112") OR ABOVE
614 985- 383 BULL POINT 300MM (12")
615 985- ... 1/2"X12")
618 985- 385 CUTTER W50X300L (2-X12")
619 985-386 SCOOP 105X405L (4 - 1/2"X16")
620 944 - 575 SYRINGE
621 980- 927 GREASE FOR HAMMER.HAMMER DRILL (500G)
NO. OPTIONAL ACCESSORIES
ITEM N
CODE NO.
Hitachi DH40FA Reviews
We have not received any reviews for Hitachi yet.